Toshiba 65NH84 owner manual Device code setup, Searching and sampling the code of a device

Page 20

Using the Remote Control

Programming the remote control for use with your audio/video devices

Device code setup

1.Refer to the Device code table on pages 22–23 to find the code for your device.

If more than one number is listed, try each one separately until you find one that works.

2.Press MODE until the Mode indicator for the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3.While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code for your device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4.Point the remote control at the device and press POWER to test the code.

If the device turns on, you have entered the correct code.

If the device does not respond to the remote control, you may have entered the wrong code. Repeat steps 3 and 4 using another code.

5.Press MODE to select the TV mode to control the TV.

Note:

•Every time you replace the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes.These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control

Searching and sampling the code of a device (8500)

TV

POWER

If you do not know the device code for a particular target unit, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that properly operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1.Press MODE to select the mode you want to set up.

2.While holding down the RECALL button, press 8 –5 –0 –0. The remote control will enter program mode.

3.Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4.If the device responds to the remote control:

Press RECALL to store the device code.

The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control: Press y, and then press POWER.

Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

CABLE/SAT LIGHT SLEEP POWER

VCR

 

DVD

1 2 3

AUDIO1Numbers

AUDIO2

4

5

6

 

 

 

MODE

 

 

 

 

 

 

 

 

MODE

 

 

 

7

 

 

8

9

 

 

PIC SIZE

 

+10

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

ACTION

 

100/

 

 

ENT

 

 

MENU

 

O

FAV

ORI

 

 

 

 

 

 

NF

 

 

T

 

 

 

 

 

I

 

 

 

TE

 

 

 

 

 

 

 

 

 

 

HE

 

 

E

 

 

 

 

 

 

LI

AT

 

 

 

 

 

 

 

 

E

ID

 

 

 

 

 

 

N

 

R

U

 

 

 

 

 

 

 

K

 

 

G

 

 

LE

SUB

TIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIT

 

 

 

 

 

 

P

 

 

 

 

LE

A

 

 

 

 

U

 

 

 

 

 

U

 

 

 

T

 

FAV

 

 

DI

 

 

y

S

 

 

 

 

 

 

 

E

 

 

 

 

O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

 

FAV

 

 

 

 

 

 

CH

 

 

 

 

 

VOL

 

 

 

DVD RTN

 

EXIT

 

 

 

 

 

RECALL

 

DVD CLEAR

 

 

 

 

CH RTN

 

INPUT

RECALL

MUTE

 

 

SLOW/DIR SKIP/SEARCH

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Projection Television Safety Precautions Dear CustomerImportant Safety Instructions InstallationService CareImportant Safety Precautions for Split Cabinet Feature Important Safety Information Introduction Welcome to Toshiba Exploring your new TVConnecting an antenna or cable TV Connecting your TVConnecting a VCR Connecting a cable converter boxConnecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting two VCRs Connecting a camcorderOne pair of standard analog audio cables Connecting an Hdmitm or a DVI device to the Hdmi inputOne Hdmi cable type a connector Connecting an audio system Preparing the remote control for use Installing the remote control batteriesUsing the Remote Control Remote Control functional key chartCBL/SAT Audio VCR TV/VCR TV/SAT Device code setup Searching and sampling the code of a deviceUsing the volume lock feature Operational feature resetConnecting YourTV Usingthe RemoteControl Setting up your TV FeaturesVCR setup codes Device code tableCD Player setup codes Learning about the remote control Connecting TVyour Learning about the menu systemChanging the on-screen display language Selecting the antenna inputPress y or z to highlight your desired language Display the pull-down menuIntroduction Connecting YourTV Adding channels to the TV’s memoryProgramming channels automatically To program channels automaticallyUp TV Changing channelsAdding and erasing channels manually Adjusting the color convergence Introduction Connecting your TVManually adjusting the color convergence Setting up your TV Using the TV’s FeaturesTo reset your adjustments Adjusting the channel settings Switching between two channels using Channel ReturnSwitching between two channels using SurfLock Programming your favorite channelsPress Enter to display the Favorite CH menu Press y or z to highlightFavorite CH Introduction Connecting YourTV Usingthe RemoteControl Settingup yourTVUsingtheTV’s Features Appendix Labeling channelsSelecting the picture size Natural picture sizeUsingtheTV’s Features Usingthe RemoteControlSetting your To lower the picture, press z Press Enter to display the Scroll Adjustment modeTo raise the picture, press y Using the Auto Aspect feature Setting Your UsingtheTV’s Features Appendix IndexPress y or z to highlight Auto ASPECT, and then press EnterUsing the POP double-window feature POP Source Select I onSwitching the main and POP pictures Switching the speaker audio main or POPUsing the programmed channel search function Double-Window aspect ratioUsing the favorite channel search function About the auto favorite featureUsing the Locks menu Using the V-CHIP menuEntering the PIN code If you cannot remember your PIN codeEnable Blocking OFF To release your setting UnlockTV Rating Independent rating system for broadcasters Press z or y to select an itemMpaa Rating Independent rating system for movies Mpaa RatingUsingthe RemoteControl Settingup YourTV Locking channelsUnlocking programs temporarily Repeat steps 2 and 3 for other channelsPress y or z to highlight Clear ALL, and then press Enter Locking the video inputs Changing the PIN codeOFF Press Enter New PIN code is now activeAdjusting the picture quality Adjusting the pictureSelecting the picture mode Selecting the color temperature Picture Settings menu appearsPress x or to select the mode you prefer Saving your new preferencesUsing the CableClear DNR feature Resetting picture adjustments Selecting the display format for 480p signals onlyTheTV’s Features Selecting the cinema modeSelecting the video input source To view text, highlight T1, T2, T3, or T4 Using the closed caption featurePress y or z to highlight Caption or TEXT, and then press Setting the on timer Setting the sleep timerTo set the clock Press y or z to highlight Clock SET, and then press EnterPress Enter to start the clock To display the time on-screen Press RecallSelecting stereo/SAP broadcasts Adjusting the soundMuting the sound Using the WOW surround sound feature Adjusting the sound qualityPress y or z to adjust the item, then press Enter Audio Settings menu appearsResetting your audio adjustments Using the StableSound featureTo turn off the StableSound feature Select OFF in above CenterConnecting Your Control Using RemoteSettingup YourTV UsingtheTV’s Features Appendix Index Turning off the built-in speakersUnderstanding the auto power off feature Understanding the last mode memory featureSelecting the background of the menu display Displaying on-screen informationSpecifications AppendixTroubleshooting AntennaBlack box appears on the screen T2, T3, or T4. Turn closed captioning OFFLimited United States Warranty Limited Canada Warranty Page Page Index Manufactured by
Top Page Image Contents