Toshiba 46HM95 owner manual Connecting an Hdmi or a DVI device to the Hdmi input

Page 19

Chapter 2: Connecting your TV

Connecting an HDMI™ or a DVI device to the HDMI input

The HDMI[1] input on your TV receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI[2] device.

This input is designed to accept HDCP[3] program material in digital form from EIA/CEA-861/861B–compliant[4]consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with 720p signals but will also accept and display 1080i, 480i, and 480p signals.

NOTE: NEVER CONNECT THIS TV

TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

To connect an HDMI device, you will need:

•one HDMI cable (type A connector) per HDMI device

For proper operation, it is recommended that you use as short an HDMI cable as possible. You should not encounter difficulty if you use an HDMI cable shorter than 16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables.

See “Setting the HDMI audio mode” on page 50.

HDMI device

HDMI OUT

VIDEOAUDIO

LR IN

LROUT

TV

OUT

__________________________________________________________________

[1]HDMI = High-Definition Multimedia Interface.

[2]DVI = Digital Video Interface.

[3]HDCP = High-bandwidth Digital Content Protection.

[4]EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

NOTE: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

•one HDMI-to-DVI adapter cable (HDMI type A connector) per DVI device

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

•one pair of standard analog audio cables per DVI device

An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below).

See “Setting the HDMI audio mode” on page 50.

DVI device

VIDEO

AUDIO

DVI/HDCP

OUT

LR IN

LROUT

TV

OUT

___________

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

 

 

Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

19

 

 

 

HM95_R1_012-25_061505

19

6/24/05, 9:12 PM

 

(E) 46/52/62HM95

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 46HM95 52HM95 62HM95 Tune Into Safety Safety PrecautionsIt Makes a Difference Where Your TV Stands IssueOn next Important Safety InstructionsInstallation, Care, and Service For replacement of the obsolete outletService Center Frequent or continuous, unplug the power cordContact a Toshiba Authorized Service Center Never attempt to service the TV yourselfContents Viewing the CableCARD menu Using the TV Guide On ScreenSee Important notes about your DLP projection TV on Features of your new TVIntroduction Welcome to ToshibaOn again to restart the lamp See LED indications onTV front touchpad and side panel controls and connections Connecting your TVGreen and Red LEDs 7 !¡ TV back panel connectionsTo a Personal Computer PC Overview of cable typesTV back panel For more information, call your local cable operatorYou will need To view encrypted digital channelsConnecting a camcorder Connecting a VCR and antenna or Cable TV no Cable boxTo view basic and premium Cable channels Connecting a VCR and Cable boxTo view basic Cable channels and use the TV’s features On Screen recording featuresFrom antenna Connecting a VCR and satellite receiverOne signal splitter Four coaxial cables Select the ColorStream HD-1 video input source on the TV To view the DVD player To view premium Cable channelsFrom antenna or Cable Your TV has ColorStream component video inputsTo view antenna or Cable channels To record a TV program while watching a DVDTo dub or edit from VCR 1 to VCR Connecting two VCRsSelect the ANT-1 video input source on the TV To view VCRTo connect an Hdmi device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputOne Hdmi cable type a connector per Hdmi device See Setting the Hdmi audio mode onConnecting an analog audio system Connecting a digital audio systemTo control the audio To connect the IR blaster cable TheaterNet on-screen device controlTo control the devices Using TheaterNet on-screen device control Connecting IEEE1394 video devicesUsing analog-compatible IEEE1394 devices Supported signalsIEEE1394 device initialization When you connect a D-VHS or Avhd device to the TVTo edit the IEEE1394 device information IEEE1394 device managementHighlight the device you want to edit and press Enter Infrared Sensor LINKconnectionTo connect to the G-LINK terminal See ChapterLearning about the remote control Using the remote controlKey for a function that is not available Effective range Remote controlRemote control and the TV Point remote control Toward remote sensor On front of TVTo install the remote control batteries Installing the remote control batteriesDevice mode control after programming Power Remote Control functional key chartAudio VCR Mute CH y VOL y Device code setupSearching and sampling the code of a device NumbersTo reset the volume controls to the original device mode Using the volume lock featureOperational feature reset Repeatedly press Mode to select CABLE/SAT modeVCRs/PVRs Multi-brand remote control device codesCable boxes DVD players CD playersReceivers Laser disksMain menu layout Menu layout and navigationYou can use the buttons on the remote Setup / Installation menu layoutButtons yzx on the remote Control or TV front panel to move Navigating the menu systemScreen 1 Select the TV location USA, and then press Setting up the TV Guide On Screen systemTo set up the TV Guide On Screen system Screen 3 Do you have Cable service connected?For additional details, see Setting up the TV Guide On Screen system TV Guide On Screen system setup. Press Enter to If your VCR did not stop playing the tape after testingData through your Cable or over-the-air video signal. If the information is incorrect, select No, repeat setupSelecting the menu language Setting up your TVConfiguring the antenna input sources To configure the ANT 1 and ANT 2 input sourcesProgramming channels automatically Programming channels into the TV’s channel memoryTo program channels automatically Manually adding and deleting channels in the channel memory Programming your favorite channels TheaterNet Setup menu opens Setting up and using TheaterNet on-screen device controlSetting up TheaterNet To set up TheaterNet device controlTo view another source Using the TheaterNet control iconsTo select the device’s control icons directly To close the on-screen control iconsMiscellaneous audio devices TheaterNet IR device codesAmplifiers Laser disk playersADC Video accessory Hdtv decoder Receivers VCRsSTS To set the Avhd device skip time Setting the time and dateSetting the Hdmi audio mode To set the Hdmi audio modeTo view the CableCARD menu Setting the Quick Restart FeatureTo set the Quick Restart feature Viewing the CableCARD menuViewing the system status Viewing the digital signal meterRating, stereo, HDTV, new episode TV Guide On Screen system includes the following featuresTo open the TV Guide On Screen system BelowNavigating the TV Guide On Screen system TV Guide On Screen remote control functionsLock/unlock icon indicates the status of the Video Window Video WindowPanel Menus System, the current program appears in the Video WindowTV Guide On Screen Icons Info Box¥ Show is presented in high-definition TV, if available Listings screen TV Guide On Screen ServicesExample Category search Search screenList of all matching shows for that keyword is displayed Search screenrfTo edit or delete a keyword To view a recording, you can do one of the following For additional details, see Record features onRecordings screen To choose the way recordings are displayedSet a show to Record from a panel menu Record featuresSchedule screen Enter to display the Record Options panel menu Don’t Record This Show-Cancels the RecordingHighlight NEW Manual Recording and press Show previously set to RecordSet a show Reminder from a panel menu Remind featuresManually set a show Reminder Reminder notification banner Change system settings Setup screenChange channel display Remind defaults Change default optionsGeneral defaults Record defaultsSource can be hidden. See page 68 for details Using the TV’s featuresSelecting the video input source to view To select the video input source to viewTo clear the input labels Labeling the video input sourcesDTV Satellite/DSS Cable Game Console To label the video input sourcesTo tune to a channel in Browse mode Tuning channelsUsing the channel browser To toggle between Browse mode and Select modeAdding channels to the channel history To set a channel as Home using the remote controlTo set a channel as Home using the menus To tune to the Home channelSwitching between two channels using SurfLock Tuning your favorite channelsTuning to the next programmed channel Switching between two channels using Channel ReturnTo select the picture size Selecting the picture sizeTheaterWide 2 picture size for letter box programs Scrolling the TheaterWide picture onNone of the picture is hidden TheaterWide 1 picture size For 43 format programTo turn off the auto aspect ratio feature Using the auto aspect ratio featureTo set the scroll settings To turn on the auto aspect ratio featureTo select the lamp mode Selecting the lamp modeTo set the Cinema Mode to Film To set the Cinema Mode to VideoTo close the POP window and tune to the highlighted window Using the POP featuresUsing the POP double-window feature To display a program in the POP windowPOP double-window aspect ratio Switching the speaker audio main or POPAspect ratio is the ratio of width to height of the picture Highlight the window for the channel you want to view Using the Freeze featureUsing the favorite channel scan feature To scan and tune your favorite channelsSelecting the picture mode Adjusting the pictureAdjusting the picture quality To select CableClear/DNR preferences Using CableClear/DNR digital noise reductionSelecting the color temperature To select the color temperatureTo select dynamic contrast preferences Using Mpeg noise reductionUsing dynamic contrast To select the Mpeg noise reduction levelTo customize the closed captions Using the closed caption modeAdvanced closed captions To view captions or textTo select digital closed captions Digital closed captionsPress Menu and open the Applications menu Selecting stereo/SAP broadcasts Adjusting the audioUsing the digital audio selector Muting the soundUsing the sub-bass system SBS Adjusting the audio qualityUsing the StableSound feature Turning off the built-in speakers Using the SRS WOW surround sound featureSelecting the optical audio output format Memory card specifications Using the memory card Jpeg picture viewer/MP3 audio playerPress to rotate the large picture 90 clockwise Using the Jpeg picture viewerTo view digital photos on your TV Press x to rotate the large picture 90 counterclockwiseTo close the picture viewer and remove the memory card Using the MP3 audio playerTo set the slide show interval To close the picture viewerMemory card care and handling Volume, and mute buttons, and then press EnterTo close the MP3 audio player To turn off the On/Off Timer Setting the On/Off Timer Setting the sleep timerTo set the sleep timer To cancel the sleep timerDisplaying the Channel Banner Understanding the auto power off featureUnderstanding the last mode memory feature Using the gray level featureChanging your PIN code Using the Locks menuEntering the PIN code If you cannot remember your PIN codeIndependent rating system for broadcasters Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies Press z to highlight Edit Rating Limits and press EnterUnlocking programs temporarily Blocking channelsLocking video inputs Using the front panel lock feature Using the GameTimerTroubleshooting V-Chip feature is available for the U.S. V-Chip system only To SAP modeRemote control batteries may be dead. Replace the batteries FeatureLED indications LED Indication Condition Solution100 TV Guide On Screen FAQs101 Why aren’t all my channels initially displayed?102 TV Guide On Screen FAQsReplacing the lamp unit Lamp unit replacement and careWhen to replace the lamp unit Appendix104 How to replace the lamp unitGrasp the lamp unit handle and gently pull the lamp unit Replace the thumb screw and hand-tighten Call Tacp Consumer Solutions atDisposing of the used lamp unit 105106 SpecificationsFor DLP Television Models Limited United States Warranty107 108 109 87Ð90 Index110 Channel programming111 Toshiba America Consumer PRODUCTS, L.L.C
Top Page Image Contents