Toshiba 46HM95 LINKconnection, To connect to the G-LINK terminal, See Chapter, Infrared Sensor

Page 25

Chapter 2: Connecting your TV

G-LINK®connection

•This connection is necessary for the TV Guide On Screen® system to work with your cable box to receive program listings and to enable the TV Guide On Screen® recording features with your VCR.

•This connection is not necessary for AVHD or D-VHS recording devices. See pages 23 and 50 for further details.

After you connect your devices to the TV, you will need to connect the G-LINK®cable (either of the dual-wand IR blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK®terminal on the TV.

Note: TV Guide On Screen® program data is available through the ANT-1 and ANT-2 antenna inputs and also through the VIDEO 1 inputs if you have a cable box connected to VIDEO 1. TV Guide On Screen® program data is not available through any other inputs on this TV. See the connection information on pages 13–25.

The G-LINK®connection is necessary to enable the following features of your TV Guide On Screen® system:

•If you have a Cable box, you need to connect the G-LINK®cable from the Cable box to the G-LINK®terminal to receive the TV Guide On Screen® program listings for your Cable service.

•If you have a VCR, you need to connect the G-LINK®cable from the VCR to the G-LINK®terminal to use the TV Guide On Screen® recording features.

To connect to the G-LINK®terminal:

Front of Cable box

 

1.Locate the infrared sensor on the front of your VCR or Cable box. The sensor is marked on some devices.*

2.Align one of the G-LINK®(IR blaster) cable’s wands about 1 inch away from the infrared sensor on the front of the VCR and attach it using double-sided mounting tape.

If you have a Cable box, attach the other wand in a similar manner. (See illustration at right.)

Note: If you do not have a Cable box, coil the second wand with a rubber band and leave it behind the TV.

3.Plug the G-LINK®(IR blaster) cable’s plug into the TV’s G-LINK®terminal.

For details on setting up the TV Guide On Screen® system:

See Chapter 5.

For details on using the TV Guide On Screen® interactive program guide:

See Chapter 7.

*If you cannot locate the device’s infrared sensor: 1. Turn OFF the device.

2.Starting at the lower left corner of the device, place the end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.)

3.If the device turns on, the point at which the remote control touched the device is the location of the sensor.

4.If the device does not turn on, move the remote control slightly to the right and press POWER again.

5.Repeat step 4 until you locate the device’s infrared sensor.

Front of VCR

Infrared

sensor

G-LINK®(IR blaster) cable wand (approx. 1 inch from device)

Back of TV

OUT

 

 

Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

25

 

 

 

HM95_R1_012-25_061505

25

6/24/05, 9:13 PM

 

(E) 46/52/62HM95

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 46HM95 52HM95 62HM95 It Makes a Difference Where Your TV Stands Safety PrecautionsIssue Tune Into SafetyInstallation, Care, and Service Important Safety InstructionsFor replacement of the obsolete outlet On nextContact a Toshiba Authorized Service Center Frequent or continuous, unplug the power cordNever attempt to service the TV yourself Service CenterContents Viewing the CableCARD menu Using the TV Guide On ScreenIntroduction Features of your new TVWelcome to Toshiba See Important notes about your DLP projection TV onOn again to restart the lamp See LED indications onTV front touchpad and side panel controls and connections Connecting your TVGreen and Red LEDs 7 !¡ TV back panel connectionsTo a Personal Computer PC Overview of cable typesYou will need For more information, call your local cable operatorTo view encrypted digital channels TV back panelConnecting a camcorder Connecting a VCR and antenna or Cable TV no Cable boxTo view basic Cable channels and use the TV’s features Connecting a VCR and Cable boxOn Screen recording features To view basic and premium Cable channelsOne signal splitter Four coaxial cables Connecting a VCR and satellite receiverSelect the ColorStream HD-1 video input source on the TV From antennaTo view the DVD player To view premium Cable channelsTo view antenna or Cable channels Your TV has ColorStream component video inputsTo record a TV program while watching a DVD From antenna or CableSelect the ANT-1 video input source on the TV Connecting two VCRsTo view VCR To dub or edit from VCR 1 to VCROne Hdmi cable type a connector per Hdmi device Connecting an Hdmi or a DVI device to the Hdmi inputSee Setting the Hdmi audio mode on To connect an Hdmi device, you will needConnecting an analog audio system Connecting a digital audio systemTo control the audio To connect the IR blaster cable TheaterNet on-screen device controlTo control the devices Using analog-compatible IEEE1394 devices Connecting IEEE1394 video devicesSupported signals Using TheaterNet on-screen device controlIEEE1394 device initialization When you connect a D-VHS or Avhd device to the TVTo edit the IEEE1394 device information IEEE1394 device managementHighlight the device you want to edit and press Enter To connect to the G-LINK terminal LINKconnectionSee Chapter Infrared SensorLearning about the remote control Using the remote controlKey for a function that is not available Remote control and the TV Remote controlPoint remote control Toward remote sensor On front of TV Effective rangeTo install the remote control batteries Installing the remote control batteriesDevice mode control after programming Power Remote Control functional key chartAudio VCR Mute Searching and sampling the code of a device Device code setupNumbers CH y VOL yOperational feature reset Using the volume lock featureRepeatedly press Mode to select CABLE/SAT mode To reset the volume controls to the original device modeVCRs/PVRs Multi-brand remote control device codesCable boxes Receivers CD playersLaser disks DVD playersMain menu layout Menu layout and navigationButtons yzx on the remote Control or TV front panel to move Setup / Installation menu layoutNavigating the menu system You can use the buttons on the remoteTo set up the TV Guide On Screen system Setting up the TV Guide On Screen systemScreen 3 Do you have Cable service connected? Screen 1 Select the TV location USA, and then pressFor additional details, see Setting up the TV Guide On Screen system Data through your Cable or over-the-air video signal. If your VCR did not stop playing the tape after testingIf the information is incorrect, select No, repeat setup TV Guide On Screen system setup. Press Enter toConfiguring the antenna input sources Setting up your TVTo configure the ANT 1 and ANT 2 input sources Selecting the menu languageProgramming channels automatically Programming channels into the TV’s channel memoryTo program channels automatically Manually adding and deleting channels in the channel memory Programming your favorite channels Setting up TheaterNet Setting up and using TheaterNet on-screen device controlTo set up TheaterNet device control TheaterNet Setup menu opensTo select the device’s control icons directly Using the TheaterNet control iconsTo close the on-screen control icons To view another sourceAmplifiers TheaterNet IR device codesLaser disk players Miscellaneous audio devicesADC Video accessory Hdtv decoder Receivers VCRsSTS Setting the Hdmi audio mode Setting the time and dateTo set the Hdmi audio mode To set the Avhd device skip timeTo set the Quick Restart feature Setting the Quick Restart FeatureViewing the CableCARD menu To view the CableCARD menuViewing the system status Viewing the digital signal meterTo open the TV Guide On Screen system TV Guide On Screen system includes the following featuresBelow Rating, stereo, HDTV, new episodeNavigating the TV Guide On Screen system TV Guide On Screen remote control functionsPanel Menus Video WindowSystem, the current program appears in the Video Window Lock/unlock icon indicates the status of the Video WindowTV Guide On Screen Icons Info Box¥ Show is presented in high-definition TV, if available Listings screen TV Guide On Screen ServicesExample Category search Search screenList of all matching shows for that keyword is displayed Search screenrfTo edit or delete a keyword Recordings screen For additional details, see Record features onTo choose the way recordings are displayed To view a recording, you can do one of the followingSet a show to Record from a panel menu Record featuresSchedule screen Highlight NEW Manual Recording and press Don’t Record This Show-Cancels the RecordingShow previously set to Record Enter to display the Record Options panel menuSet a show Reminder from a panel menu Remind featuresManually set a show Reminder Reminder notification banner Change system settings Setup screenChange channel display General defaults Change default optionsRecord defaults Remind defaultsSelecting the video input source to view Using the TV’s featuresTo select the video input source to view Source can be hidden. See page 68 for detailsDTV Satellite/DSS Cable Game Console Labeling the video input sourcesTo label the video input sources To clear the input labelsUsing the channel browser Tuning channelsTo toggle between Browse mode and Select mode To tune to a channel in Browse modeTo set a channel as Home using the menus To set a channel as Home using the remote controlTo tune to the Home channel Adding channels to the channel historyTuning to the next programmed channel Tuning your favorite channelsSwitching between two channels using Channel Return Switching between two channels using SurfLockTo select the picture size Selecting the picture sizeNone of the picture is hidden Scrolling the TheaterWide picture onTheaterWide 1 picture size For 43 format program TheaterWide 2 picture size for letter box programsTo set the scroll settings Using the auto aspect ratio featureTo turn on the auto aspect ratio feature To turn off the auto aspect ratio featureTo set the Cinema Mode to Film Selecting the lamp modeTo set the Cinema Mode to Video To select the lamp modeUsing the POP double-window feature Using the POP featuresTo display a program in the POP window To close the POP window and tune to the highlighted windowPOP double-window aspect ratio Switching the speaker audio main or POPAspect ratio is the ratio of width to height of the picture Using the favorite channel scan feature Using the Freeze featureTo scan and tune your favorite channels Highlight the window for the channel you want to viewSelecting the picture mode Adjusting the pictureAdjusting the picture quality Selecting the color temperature Using CableClear/DNR digital noise reductionTo select the color temperature To select CableClear/DNR preferencesUsing dynamic contrast Using Mpeg noise reductionTo select the Mpeg noise reduction level To select dynamic contrast preferencesAdvanced closed captions Using the closed caption modeTo view captions or text To customize the closed captionsTo select digital closed captions Digital closed captionsPress Menu and open the Applications menu Using the digital audio selector Adjusting the audioMuting the sound Selecting stereo/SAP broadcastsUsing the sub-bass system SBS Adjusting the audio qualityUsing the StableSound feature Turning off the built-in speakers Using the SRS WOW surround sound featureSelecting the optical audio output format Memory card specifications Using the memory card Jpeg picture viewer/MP3 audio playerTo view digital photos on your TV Using the Jpeg picture viewerPress x to rotate the large picture 90 counterclockwise Press to rotate the large picture 90 clockwiseTo set the slide show interval Using the MP3 audio playerTo close the picture viewer To close the picture viewer and remove the memory cardMemory card care and handling Volume, and mute buttons, and then press EnterTo close the MP3 audio player To set the sleep timer Setting the On/Off Timer Setting the sleep timerTo cancel the sleep timer To turn off the On/Off TimerUnderstanding the last mode memory feature Understanding the auto power off featureUsing the gray level feature Displaying the Channel BannerEntering the PIN code Using the Locks menuIf you cannot remember your PIN code Changing your PIN codeTo block and unblock TV programs and movies Blocking TV programs and movies by rating V-ChipPress z to highlight Edit Rating Limits and press Enter Independent rating system for broadcastersUnlocking programs temporarily Blocking channelsLocking video inputs Using the front panel lock feature Using the GameTimerTroubleshooting Remote control batteries may be dead. Replace the batteries To SAP modeFeature V-Chip feature is available for the U.S. V-Chip system onlyLED indications LED Indication Condition Solution100 TV Guide On Screen FAQs101 Why aren’t all my channels initially displayed?102 TV Guide On Screen FAQsWhen to replace the lamp unit Lamp unit replacement and careAppendix Replacing the lamp unit104 How to replace the lamp unitGrasp the lamp unit handle and gently pull the lamp unit Disposing of the used lamp unit Call Tacp Consumer Solutions at105 Replace the thumb screw and hand-tighten106 SpecificationsFor DLP Television Models Limited United States Warranty107 108 109 110 IndexChannel programming 87Ð90111 Toshiba America Consumer PRODUCTS, L.L.C
Top Page Image Contents