Enterasys Networks 9033348-02 manual RoamAbout Lightning Protector

Page 58

RoamAbout Lightning Protector

RoamAbout Lightning Protector

The RoamAbout Lightning Protector is a surge arrestor that protects your sensitive RoamAbout equipment from high-voltage currents caused by discharge and transients at the antennas.

Table A-8 lists the specifications for the RoamAbout Lightning Protector.

Table A-8: Lightning Protector Specifications

Mechanical

Size

Height

69 mm (2.7 in)

Diameter

26 mm (1 in)

 

 

 

Weight

 

133 g (4.7 oz.)

 

 

Connectors

 

 

 

 

FCC Countries

Reverse Polarity-N (Male on both ends)

 

 

 

ETSI Countries

Standard-N (Female on both ends)

 

 

 

France

Standard-N (Female on both ends)

 

 

 

Japan

Standard-N (Female on both ends)

 

 

 

Asia Pacific

Standard-N (Male on both ends)

 

 

Operating Temperature

-40°C to +85°C (-40°F to +185°F)

 

 

Electrical

 

 

 

Frequency Range

800-2500 MHz

 

 

Insertion Loss

0.2 dB

 

 

Surge Current

2000 Amp

 

 

Nominal Impedance

50 Ohms

Specifications A-8

Image 58
Contents Outdoor Antenna Site Preparation and Installation Guide Page Page Regulatory Information Electrical Hazard Warnings Page Contents Antenna Installation Preface Intended AudienceAssociated Documents Component Information LocationGetting Help Address TechWriting@enterasys.comDocument Conventions Icon MeaningChoosing a Wireless Network Configuration Chapter Site PreparationDetermining the Antenna Locations Maximum Distances Between AntennasDistances and Line of Sight Clearance FCC RoamAbout PC Card Variations Line of SightFresnel Zone and Line of Sight Clearance Potential Obstacles to Line of Sight not to scale Other Factors That Can Reduce Antenna Range Large Reflecting SurfacesInstaller is responsible for local building codes Other RequirementsAntenna Options RoamAbout 5 dBi Vehicle-Mount AntennaRoamAbout 14 dBi Directional Antenna KITExample Outdoor Yagi Antenna Configuration RoamAbout 7 dBi Omni-Directional Antenna Antenna KITExample Omni-Directional Antenna Configuration Mounting Requirements Contacting an Antenna Installation CompanyLightning Protection Line of SightInstallation Requirements Page Chapter Access Point Placement Configuration Determining the Location of the Access PointOverview of Connecting Cables to the Access Point Access Point 2000 Installation OverviewOverview of Connecting Cables to the Access Point Overview of the Access Point Configuration Settings from the RoamAbout Access Point Installation MenuRoamAbout Access Point Manager Overview of the Access Point Configuration Chapter Antenna Installation Installation Overview Verify Component Connector PolaritySelecting the Correct N-Type Connector Lightning Protector Installation Grounding SystemLightning Protector Installation Mounting the Antenna Antenna Polarization Mounting the Directional Antenna Antenna Cables section onMounting the 14 dBi Antenna to a Mast Mounting the Omni-Directional Antenna Mounting the Omni-Directional Antenna to a Mast Mounting the Vehicle-Mount Antenna Mounting the Vehicle-Mount AntennaConnecting the Antenna Cables Antenna Cable RouteConnecting the Cables Optimizing RoamAbout Outdoor Antenna Placement Routine Maintenance Table A-1 14 dBi Directional Antenna Specifications RoamAbout 14 dBi Directional AntennaRoamAbout 14 dBi Directional Antenna Table A-2 7 dBi Omni-Directional Antenna Specifications RoamAbout 7 dBi Omni-Directional AntennaTable A-3 Vehicle-Mount Antenna Specifications Vehicle-Mount Antenna Table A-4 Pigtail Connection Specifications RoamAbout Pigtail ConnectionMechanical Specifications Low-Loss Antenna CableConnectors Table A-8 Lightning Protector Specifications RoamAbout Lightning Protector