LG Electronics HR931M, HR935M, HR939M, HR932M, HR933M owner manual About the internal, Hard disk drive

		Appendix 87
to [DTS re-encode], the audio output is limited	About the internal
*5 If the [HDMI] or [Digital Output] option is set	hard disk drive
Output] option is set to [DTS re-encode], the
to 48 kHz and 5.1Ch. If the [HDMI] or [Digital
DTS Re-encode audio is output for BD-ROM	The internal hard disk drive (HDD) is a fragile piece
discs, and the original audio is output for the
other discs (like [Primary Pass-Thru]).	of equipment. Please use the player following the
yy If [HDMI] option is set to [PCM Multi-CH] and	guidelines below to protect against possible HDD
	failure.
[Digital Output] option is set to [Primary Pass-
	yy Do not move the player while it is on.
Thru], it plays Dolby Digital Plus.
yy If the HDMI connection is version 1.3 and Dolby	yy Install and use a player on a stable, levelled
Digital Plus/Dolby TrueHD is output from HDMI	surface.
OUT jack.	yy Do not use the player in excessively hot or
yy The audio is outputted as PCM 48 kHz/	humid places, or in places that may be subject
16 bit for MP3/WMA file and PCM	to sudden changes in temperature. Sudden
44.1 kHz/16 bit for Audio CD while playback.	changes in temperature can cause condensation
yy The Dolby TrueHD audio recorded on some Blu-	to form inside the player. This can be a cause of
	HDD failure.
ray discs consists of Dolby Digital and TrueHD
	yy While the player is powered on, do not unplug
audio. Dolby Digital audio is output through
DIGITAL AUDIO OUT jacks and “DD” displays on	from the wall socket or switch the electricity off
the screen if TrueHD audio is not output (for	from the breaker switch.
example, when [HDMI] is set to [PCM Stereo] and	yy Do not move the player immediately after
[Digital Output] is set to [Primary Pass-Thru]).	switching it off. If you need to move the player,
yy You must select a digital audio output and	please follow the steps below:
a maximum sampling frequency that your	1.	After the message “OFF” is shown in the
Amplifier (or AV receiver) accepts using [Digital
		display, wait at least two minutes.
Output], [HDMI] and [Sampling Freq.] options on
the [Setup] menu (see page 33-34).	2.	Unplug from the wall socket.
yy With digital audio connection (DIGITAL AUDIO	3.	Move the player.
OUT or HDMI), Disc Menu button sounds of BD-

ROM may not be heard if the [Digital Output] or	yy If there’s a power failure while the player is on,
	there is a chance that some data on the HDD will
[HDMI] option is set to [Primary Pass-Thru].
	be lost.
yy If the audio format of the digital output does
	yy The HDD is very delicate. If used improperly or
not match the capabilities of your receiver, the
	in an unsuitable environment, it is possible that
receiver will produce a strong, distorted sound
	the HDD will fail after a few years of use. Signs
or no sound at all.
	of problems include playback unexpectedly
yy Multi-channel Digital Surround Sound via digital
	freezing and noticeable block noise (mosaic) in
connection can only be obtained if your receiver
	the picture.
is equipped with a Digital Multi-channel decoder.
	yy However, sometimes there will be no warning
	signs of HDD failure.
	yy If the HDD fails, playback of content will not
	be possible. In this case, contact the LG service
	center by following methods.
	Web: http://lgservice.com
	yy The manufacturer disclaims responsibility for loss
	of data contained in internal HDD.
	yy There are some capacities in HDD reserved for
	the file system and timeshift.

6

Appendix