Transmitter Safety Features

Adjusting the Flame Height -

Operates in ON or THERMO mode

This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER.

1.Press and release FLAME button to change ﬂame height to HI (see Figure 8, Location #5), (a second ﬂame icon appears).

2.Press again to return ﬂame to normal state.

Low/Battery Indicator

An “X” outlined by a battery on the right side of the LCD screen will appear when battery power has dropped sig- niﬁcantly. At this time, approximately two weeks of battery power remains.

Child Proof Lockout (CP)

The transmitter contains a “Child Proof” lockout feature that prevents unauthorized use of the remote control. To access the “Child Proof” activation button, remove cover on BACK of transmitter. To activate LOCKOUT:

1.Press and hold in the “setting button” for 5 seconds. The letters CP will display on the LCD screen (see Figure 8). This prevents the activation of ﬁreplace. When any function button is pressed ON/OFF etc. the letter CP will display on the LCD screen.

To deactivate LOCKOUT:

1.Press and hold in the “setting button” for 5 seconds. The LCD will display CP until 5 seconds have elapsed, and then the LCD screen will return to its normal state.

It is recommended that the TRANSMITTERS always be located within a 20 foot operating range of the ﬁreplace, preferably in the same room in which the ﬁreplace system is located. The TRANSMITTER features several safety features that alert the user when the TRANSMITTER is placed outside the 20 foot normal operating range.

Thermo-Updating and Communication-Safety Fea- tures

This remote control has a COMMUNICATION-SAFETY function built into its software. It provides an extra margin of safety when the TRANSMITTER is out of the normal 20 foot operating range of the receiver. It is also activated when the batteries become weak or are removed from the transmitter.

In the THERMO-UPDATING feature (only in the THERMO or TIMER modes) the transmitter normally reads the ROOM temperature every 2 minutes. In addition to checking the temperature, the transmitter sends a signal to the receiver in- dicating that the transmitter and its batteries are still active.

In the COMMUNICATION-SAFETY feature, at all times and in all OPERATING MODES the transmitter sends a signal every ﬁfteen (15) minutes to the receiver, indicating that the transmitter is within the normal operating range of 20 feet.

Should the receiver NOT receive a transmitter signal every 15 minutes (COMMUNICATION-SAFETY feature), the RE- CEIVER will begin a 2 HOUR (120 minute) countdown tim- ing function. If during this 2 hour period, the receiver does not receive a signal from the transmitter, the RECEIVER will shut down the ﬁreplace being controlled by the receiver. The RECEIVER will then emit a series of rapid “beeps”. Then, after 10 rapid “beeps”, the RECEIVER will continue to emit a single “beep” every 4 seconds until a transmitter signal is again received. The intermittent 4 second beeping will go on indeﬁnitely until reset.

To “reset” the RECEIVER and operate the ﬁreplace system:

1.Press the MODE button on the transmitter. The word ON must display on the LCD screen. The COMMUNICA- TION -SAFETY operation is overridden and the system will return to normal operation depending on the MODE selected at the transmitter.

We recommend the user check the batteries in the TRANSMITTER to make sure the voltage is no less than 2.7 volts.

Auto Shutdown

This remote control has an Auto Shutdown feature incor- porated into its system. When the transmitter MODE is in the ON position the ﬁreplace will continuously operate for 9 hours. After 9 hours, the ﬁreplace will shut down. To relight the ﬁreplace:

1.Press the MODE button. The ﬁreplace will operate continuously for up to 9 hours before Auto Shutdown repeats cycle. The Auto Shutdown signal comes from the transmitter. The transmitter must be positioned within a 20 foot operating range for the Auto Shutdown feature to operate.

SYSTEM CHECK

Millivolt Valves

Light the appliance following the lighting instructions that came with the ﬁreplace. Conﬁrm that the pilot ﬂame is on. It must be in operation for the main gas valve to operate.

1.Slide the 3-position button on the remote receiver to the ON position. The main gas ﬂame (i.e., the ﬁre) should ignite.

2.Slide the button to OFF. The ﬂame should extinguish (the pilot ﬂame will remain on).

3.Slide the button to REMOTE (the center position), then press the MODE button on the transmitter to change the system to ON. The main gas ﬂame should ignite.

4.Press the MODE button on the transmitter to change the system to OFF. The ﬂame should extinguish (the pilot ﬂame will remain on).

5.Press the MODE button on the transmitter to change the system to THERMO.

6.Advance the SET temperature on the transmitter to a temperature of at least 2º F (1º C) above the ROOM temperature displayed on the LCD screen and the system ﬂame will ignite.

RCTS-MLT specifications

Hearth and Home Technologies has established itself as a leader in the home heating and comfort industry, and their RCTS-MLT model exemplifies this commitment through its innovative features and advanced technology. Designed for both functionality and aesthetic appeal, the RCTS-MLT is a radiant catalytic technology stove that offers warmth while accentuating the decor of any space.

One of the standout features of the RCTS-MLT is its radiant heating capability. This technology allows for an efficient and even distribution of heat throughout the room, ensuring that every corner is warm and inviting. The catalytic combustion process significantly reduces emissions, making the stove an environmentally friendly choice for homeowners seeking sustainable heating solutions.

Aesthetically, the RCTS-MLT is designed with elegance in mind. Its contemporary styling and multiple finish options ensure that it can seamlessly fit into various interior designs, whether traditional, modern, or rustic. The large glass window provides an unobstructed view of the flames, creating a cozy ambiance in any living space. Additionally, the adjustable airflow control allows users to customize their heating experience, optimizing comfort while maintaining efficiency.

The RCTS-MLT is also equipped with user-friendly features that enhance the overall experience. The remote control capability enables users to adjust settings from a distance, adding convenience to the operation. With a built-in thermostat, the stove can automatically regulate the temperature, providing consistent warmth without the need for manual adjustments.

Durability and reliability are at the core of the RCTS-MLT’s design. Constructed from high-quality materials, the stove is built to withstand the rigors of regular use while maintaining its performance. It is also designed for easy cleaning and maintenance, ensuring that it remains in optimal condition for years to come.

In summary, the Hearth and Home Technologies RCTS-MLT stands out in the home heating market due to its combination of radiant catalytic technology, stylish design, user-friendly features, and durability. It presents an exceptional choice for those looking to enhance their home’s comfort and aesthetic while being mindful of environmental impacts. Whether you are heating a living room, a den, or a spacious open area, the RCTS-MLT delivers an exceptional heating experience that balances efficiency with elegance.