Mitsubishi Electronics XL5950U user manual Basic connections, Projector + AV device

Page 10

Basic connections

This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal computer that have analog RGB output connectors.

Important:

Make sure that the connected device is turned off before starting connection.

Plug in the projector and the connected devices firmly, and unplug them by holding and pulling out their power plugs, not by pulling the power cords.

When the projector and the connected devices are located too close to each other, the projected image may be affected by their interference.

See the owner’s guide of each device for details about their connections.

Projector + AV device

Important:

Connect the video and audio plugs of the AV cable to the proper terminals matching their colors respectively.

When the connected AV device uses a BNC connector for its video output, connect it to the VIDEO 1 (BNC) terminal. When both the VIDEO 1 (BNC) terminal and the VIDEO 2 (RCA) terminal are engaged at the same time, the image supplied to the VIDEO 2 (RCA) terminal takes priority.

When the connected AV device uses a BNC connector for its S-video output, connect it to the VIDEO 2 (Y,C)(BNC) terminal. When both the VIDEO 2 (Y,C) (BNC) terminal and the S-VIDEO 2 terminal are engaged at the same time, the image supplied to the S-VIDEO 2 terminal takes priority.

When using the video (RCA) or S-video connector When using the BNC connector

 

S-VCR, etc.

VCR, etc.

To S-video output

 

 

 

To audio output

 

To S-video input

To video output

 

To video input

To audio input

Projector + DVD player or HDTV decoder

S-VCR, etc.VCR, etc.

To Y output

To S output

To audio output

To Y input

To video output

To S input

To audio input

To video input

Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such a DVD player with this projector, use the COMPUTER/COMPONENT VIDEO INPUT 1 terminal.

DVD player or HDTV decoder

 

BNC-BNC cable (option)

 

 

CB(PB)

B

B/PB

Y

G

G/Y

CR(PR)

R

R/PR

to AUDIO OUT

BNC-RCAconnector (option)

COMPUTER AUDIO IN

AUDIO cable (option)

The terminals’ names Y, PB, and PR are examples of a case where a HDTV decoder is connected.

The terminals’ names are different depending on the connected devices.

Use BNC-BNC cables for connection.

The image may not be projected correctly with some DVD players.

When connecting a HDTV decoder having RGB output terminals, set the COMPUTER INPUT to RGB in the SIGNAL menu.

EN – 10

Image 10
Contents L5950 X L5900 When using the projector in Europe Compliance NoticeContents Important safeguards It can lead to fire Lens may shift causing injury or damage to the projectorIt can lead to fire or electric shock If you use incorrect voltage, it can lead to fireOverview Terminal panelHow to enable the Laser button How to disable the Laser buttonAbout the laser beam Operation area for wireless control system Using the remote controlBattery installation Using the wired remote controlFront projection Front projection, ceiling mount InstallationOrientation of the projector Rear projectionProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder For Macintosh Projector + ComputerAbout DDC Preparing the projector for operation Adjusting the angle of projectionRotate the adjustment feet for fine adjustment Getting ready for projectionTo operate projector power on ConditionTurning off the projector Volume from the speakerAnamorphic mode AV muteBasic operation Menu operationPress the Enter button or button An externally connected power switch such as a breaker even Is off. Use the remote control to turn on the lampUse to adjust the horizontal position of the image Expand Mode .. Select the mode for enlarging screen. SeeAutomatically selected depending on the input signal. If Use to adjust the vertical position of the imageAdjusting the image Picture adjustmentUser memory for signal setting Color matrixColor temperature Adjustment from personal computerPicture in Picture PinP Advanced features for presentationExpand StillOperation Mouse remote controlProjector + computer with USB connector Projector + computer with Serial portInterval of the lamp replacement Lamp replacementHow to reset the operation time meter Cleaning the projector and the ventilation slots MaintenanceCleaning the air-filter Cleaning the lensHow to check battery level Procedure for setting the Anti-Theft Alarm deviceProcedure for changing batteries Insert dry cell batteries into the theft warning deviceTroubleshooting Normal condition IndicatorsUnusual temperature Abnormal conditionSpecifications Replacement part Option / Not included in the box ConnectorsDimensional drawings mm What’s included in the boxCGA70 With Long Throw Zoom Lens OL-X500LZ With Short Throw Zoom Lens OL-X500SZWith Tele Throw Zoom Lens OL-X500TZ With Rear projection Short Throw OL-X500FR F2.5Mitsubishi Electric Corporation
Related manuals
Manual 6 pages 62.95 Kb