Mitsubishi Electronics XL5950U Expand Mode .. Select the mode for enlarging screen. See, Manually

HOLD

USER MEMORIZE

MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT

3 FEATURE

opt.

XGA60

MENU POSITION ....... Use to select the position of the menu on the screen,

(upper

left) or

(lower right).

FEATURE

EXPAND MODE .. Select the mode for enlarging screen. See page 20.

MENU POSITION

1.

FRAME POSI. ...... Sets the position of sub screen. See page 20.

VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is

A

EXPAND MODE

1.

A

automatically selected depending on the input signal. If the

FRAME POSI.

3.

A

A

image isn’t displayed correctly, select the desired video format

?

VIDEO SIGNAL

AUTO

manually.

SCART INPUT

OFF

SCART ................. Select ON when connecting with a device equipped with the

ANAMORPHIC

OFF

SCART terminal that can output RGB signal. SCART terminal

is used mainly in Europe. Select OFF normally.

3D CineView

ON

ANAMORPHIC .... Select the desired position, UPPER, CENTER or LOWER when

LANGUAGE

English

A

Ë

playing DVD discs containing data of letterboxed images.

RESET ALL

OK

3D Cine View ........ Select ON for high quality video image. Select ON normally.

LANGUAGE ........ Use to select the language used in the menus. (

/ English / Español / Deutsch / Français / Italiano

/ /

/

/

)

RESET ALL ......... Use to reset the MENU settings (except LANGUAGE).

•When SCART is set to ON, nothing is output to the external monitor.

•When SCART is set to ON, normal computer signals are not projected.

•Use SCART-BNC (or SCART-Mini D-SUB 15P) cable (option), when connecting with AV device equipped with the SCART terminal.

•Some AV devices equipped with the SCART terminal may not be compatible with the projector.

•When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of VIDEO SIGNAL depending on the input signal in such cases.

•When 3D Cine View is switched from OFF to ON, you can check the motion detection operation about three seconds. The buttons on the remote control don’t work during this period, which isn’t a failure.

•When the LANGUAGE in FEATURE menu is set to English and NTSC video format is selected, the brightness is decreased 15 points by set-up cancel function for U.S. (The indicated value is not changed.) The image becomes darker, but this is not a failure of the projector.

ENGLISH

4 SIGNAL
MEMORY CALL	Use to select AUTO, USER 1 or USER 2. See page 18.
HORIZ. POSITION	Use to adjust the horizontal position of the image.
VERT. POSITION	Use to adjust the vertical position of the image.
FINE SYNC	Use to synchronize the projector with PC input signals so that
	the image is not blurred.
TRACKING	Use to avoid image noise such as wide stripes.
COMPUTER INPUT	The unit adjusts itself automatically when connected to a DVD
	player with a component video output (Y, CB, CR). In the case the
	projector is connected to equipment that includes RGB output
	terminal, adjust to RGB mode.
HOLD	Adjusts the image when flagging occurs near the top of the
	screen.

SIGNAL

A

U

R G B

R G B

opt.

XGA60

AUTO

0

0

0

0

RGB

AUTO

DELETE DEFAULT

5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/	SIGNAL-USER
CLAMP WIDTH .......... If you use something similar, the brighter colors of the projected
	CLAMP POSITION	0
image may become blurred. In this case, adjust CLAMP POSITION
	CLAMP WIDTH	0
or CLAMP WIDTH.
	HORIZ. PIXELS	0
HORIZ.PIXELS .... Use to adjust the width of the image. The image size grows wider as
the number increases. (Adjust to the horizontal pixels of the input	VERT. LINES	0
signal for normal setting.)
	VERT. SYNC.	AUTO
VERT.LINES ....... Use to adjust the height of the image. The image size grows higher
	SHUTTER(U)	0
as the number increases. (Adjust to the vertical lines of the input
	SHUTTER(L)	0
signal for normal setting.)
	SHUTTER(LS)	0
VERT.SYNC. ........ Use to adjust the image when its motion does not run smoothly.
Select AUTO for normal setting.	SHUTTER(RS)	0
SHUTTER(U) ....... Use to adjust the image when the noise etc. appears on top part of
image.
SHUTTER(L) ....... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) ..... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ..... Use to adjust the image when the noise etc. appears on right side of image.

•When the setting of the SIGNAL-USER menu is changed, the image may not be displayed correctly. In this case, select DEFAULT in the SIGNAL menu, and press the ENTER button.

EN – 17