Mitsubishi Electronics XL5950U user manual Using the remote control, Battery installation

Page 8

Using the remote control

Battery installation

Use two AA size batteries.

1.Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.

2.Load the batteries making sure that they are positioned correctly (+ to +, and - to -).

• Load the batteries from - spring side, and make sure to set them tightly.

3.Replace the back cover.

1

2

3

Important:

Do not use a new battery with an old one.

Load batteries in the correct position.

Do not heat, take apart, or throw batteries into fire.

Do not try to recharge batteries. Do not use rechargeable batteries.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

Operation area (for wireless control system)

The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The dis- tance to the screen back to the projector must be less than 7 m (about 23 feet). Depending on the type of the screen, the distance will be different.

20˚

15˚

20˚

15˚

30˚

30˚

20˚

20˚

Important:

Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m (6.5 feet) between the remote control sensor and fluorescent lamp on the remote control may not work correctly.

Using the wired remote control

Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired remote control is useful for operating in a distance or outside of the operating area.

REMOTE IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB

• When REMOTE OUT terminal on this projector is connected to

 

 

 

 

 

RS-232C

RS-232C/MOUSE

 

REMOTE REMOTE

INPUT 1

R/PR

G/Y

B/PB

H/HV

V

 

IN

OUT

the REMOTE OUT terminal on the other projector, the two

MAIN

 

INPUT 2

 

AUDIO

 

 

VIDEO

projectors can be controlled together by using the remote

 

 

 

 

IN

 

S-VIDEO

2

 

 

 

 

 

Y

 

VIDEO

control. (Up to two projectors can be controlled.)

 

AC IN

 

 

AUDIO

C

 

1

 

 

 

 

 

OUT

 

 

 

 

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

R

REMOTE OUT

 

 

 

 

 

 

 

REMOTE IN

 

 

 

 

 

 

 

 

When the remote control is connected with remote control cable, it does not work as a wireless remote control.

For connection, use the pin-pin cable of ø3.5 stereo type, which is commercially available. However, some cable may not work correctly.

When using the wired remote control, the laser beam may be darker. It is normal.

EN – 8

Image 8
Contents L5950 X L5900 When using the projector in Europe Compliance NoticeContents Important safeguards Lens may shift causing injury or damage to the projector It can lead to fire or electric shockIt can lead to fire If you use incorrect voltage, it can lead to fireOverview Terminal panelAbout the laser beam How to disable the Laser buttonHow to enable the Laser button Using the remote control Battery installationOperation area for wireless control system Using the wired remote controlInstallation Orientation of the projectorFront projection Front projection, ceiling mount Rear projectionProjector + DVD player or Hdtv decoder Basic connectionsProjector + AV device About DDC Projector + ComputerFor Macintosh Adjusting the angle of projection Rotate the adjustment feet for fine adjustmentPreparing the projector for operation Getting ready for projectionTo operate projector power on ConditionVolume from the speaker Anamorphic modeTurning off the projector AV mutePress the Enter button or button Menu operationBasic operation An externally connected power switch such as a breaker even Is off. Use the remote control to turn on the lampExpand Mode .. Select the mode for enlarging screen. See Automatically selected depending on the input signal. IfUse to adjust the horizontal position of the image Use to adjust the vertical position of the imagePicture adjustment User memory for signal settingAdjusting the image Color matrixColor temperature Adjustment from personal computerAdvanced features for presentation ExpandPicture in Picture PinP StillMouse remote control Projector + computer with USB connectorOperation Projector + computer with Serial portHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Maintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensProcedure for setting the Anti-Theft Alarm device Procedure for changing batteriesHow to check battery level Insert dry cell batteries into the theft warning deviceTroubleshooting Indicators Unusual temperatureNormal condition Abnormal conditionSpecifications Connectors Dimensional drawings mmReplacement part Option / Not included in the box What’s included in the boxCGA70 With Tele Throw Zoom Lens OL-X500TZ With Short Throw Zoom Lens OL-X500SZWith Long Throw Zoom Lens OL-X500LZ With Rear projection Short Throw OL-X500FR F2.5Mitsubishi Electric Corporation
Related manuals
Manual 6 pages 62.95 Kb