
Connecting MonitorLink™, NetCommand® IR Emitter
Note: The TV back panel and connections shown here are for reference only and may vary by model.
MonitorLink/DVI
(Figure 14)
1.Connect a MonitorLink/DVI cable from the TV back panel to the Mitsubishi HD Receiver/ Controller back panel.
2.Connect the MonitorLink
3.Connect the L (left) and R (right) audio cables from the HDTV receiver to AUDIO LEFT and AUDIO RIGHT on the MonitorLink section of the TV back panel.
|
|
| ||||||||
|
|
| back panel |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| DTV(YPbPr/ GBRHV ) |
|
|
|
|
|
|
|
|
|
| 480i / 480P /1080 i |
|
|
|
|
|
|
|
|
| Y |
|
|
|
|
|
|
|
|
|
| G | 403XF- |
|
|
|
|
|
|
|
|
| B | |
|
|
|
|
|
|
|
| 2 | Pb |
|
|
|
|
|
|
|
|
| P r | 5K | |
|
|
|
|
|
|
|
|
| R | V |
| Mitsubishi |
|
|
|
|
|
|
| ||
| receiver/controller back panel |
|
|
|
|
| ||||
|
|
|
|
|
| OUTPUTS |
|
|
| |
|
|
|
|
| TO |
| TO |
|
|
|
|
|
| INPUT |
| AV RECEIVER | DISPLAY |
|
|
| |
|
|
|
|
|
|
|
|
|
| |
| 1 | 2 | 3 | 4 | MONITOR | PIP |
|
|
| |
|
|
|
|
|
|
|
|
|
| |
| VIDEO |
|
|
|
|
|
|
| White | 3 |
|
|
|
|
|
|
|
|
| ||
| AUDIO |
|
|
|
|
|
|
|
|
|
| LEFT |
|
|
|
|
|
|
|
|
|
| AUDIO |
|
|
|
|
|
|
|
|
|
AC IN | RIGHT |
|
|
|
|
|
|
| Red |
|
|
|
| IR OUTPUT | MonitorLink TM |
| DIGITAL AUDIO | MonitorLinkTM |
|
| |
|
| NetCommand R |
| OUTPUT | /DVI |
|
| |||
|
|
|
|
|
|
|
|
| 1 | |
|
|
|
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ferrite | |
|
|
|
|
|
|
|
|
| core |
|
MONITORLINK | /DVI | ferrite |
|
| |
|
| core |
MONITORLINK | 1 | |
CONTROL |
White 3
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
Red
NOTE: The 29 pin MonitorLink/DVI and
IR Emitter Repeater and
NetCommand® IR
(Figure 15) (WS-, WS-, WS-)
The two IR jacks labeled REPEATER are not used by NetCommand, but will repeat any IR command received by the TV. The NetCommand® IR jacks are used by NetCommand to control external devices. They both connect the same way:
1.Connect one of the IR emitters to one IR EMITTER jacks on the TV back panel.
2.Place the IR emitter cable under or on top of each A/V device. Place the IR lens directly in front of the A/V device infrared signal receiver, usually located behind the front translucent panel of the receiver.
3.If you are connecting to only one A/V device, place the unused transmitter in an
4.For permanent installation of the IR emtter cable, use the included double sided adhesive tape to secure the body of the emitter to the A/V receiver, DVD player, Cable box, etc...
Figure 14. Connecting MonitorLink
CAUTION: To assure continued FCC compliance, the user must use a shielded video interface cable with bonded ferrite cores at both ends, when using the MonitorLink/DVI input.
IR EMITTER
REPEATER | NetCommandR IR |
use with |
|
|
| use with |
|
|
| NetCommand | |
|
|
| ||
|
|
| controlled devices | |
controlled devices |
|
|
| |
| or |
|
| |
|
|
|
|
Ferrite Core | 1 |
|
| Other A/V Device |
|
|
| A/V Receiver | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2
Figure 15. Connecting IR Emitters WS-48413, WS-55413, WS-65413
Do not use the IR emitter connections with devices that can receive the remote control signal directly, as the signals can interfere with each other.
21