JVC HD-65S998 manual Table of signals for each type of computer, When a picture is not displayed

Page 24

Quick Setup

Table of signals for each type of computer

Resolution	Vertical	Horizontal
	Frequency	Frequency
	(Hz)	(kHz)

640 x 480	60.0	31.5
(VGA)

1024 x 768	60.0	48.4
(XGA)

•Only the above formats are supported.

•Even with the above formats at 60 Hz, some problems may be experienced depending on the quality of the synchronous signal. (Depending on the quality, some pictures may not be displayed correctly).

•Apple Macintosh* computers are not supported.

When a picture is not displayed

With some computers, some problems can be solved by changing the settings. Check the computer's refresh rate and set it to 60Hz. Computers that cannot set the refresh rate to 60 Hz, can not be used with this TV. Refer to the computer's instruction manual.

*Apple Macintosh is a registered trademark of Apple Computer, Inc.

Note:

•If you are inputting a PC signal that is invalid, "Invalid Signal" will appear on the TV screen. It appears when the input is PC and it is a single screen.

24

Image 24

Contents Projection Television Users Guide Important Safety Precautions Important Safety Instructions FCC Notice Caring for the Cabinet Caring for the ScreenWhen the power is turned on, the warming up commences Order to use the television for a long timeCooling the inside of the television and the lamp Lamp is a consumable itemTelevision requires a lot of electrical power ILA element characteristicsScreen is made of plastic Do not replace the lamp immediately after useAttaching or removing the pedestals To attach the front and rear pedestalTo remove the front and rear pedestal Table of Contents Quick Setup Unpacking your TVSide Panel Diagram Front Panel DiagramTV Model Remote Control RM-C1400Using Menu Buttons Basic OperationGetting Started Connecting Your Devices Coaxial CablesVideo Cable Component Cables Composite Cables Audio CablesVCR Connection Diagram #2 Connecting to a Camcorder CamcorderConnecting to an External Amplifier Connecting to an amplifier using your optical outputConnecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT Connecting to the computer Looking at the images from a computerTable of signals for each type of computer When a picture is not displayedLanguage Interactive Plug In MenuAuto Clock Set Manual Clock SetAuto Tuner Setup NOW ProgrammingUsing the Guide Onscreen MenusOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option BlueTo Initial Setup Initial Setup CLOCK/TIMERSAuto Tuner Setup Channel Summary Digital ChannelsContinue to follow these directions for all four spaces Channel Guard Message ChipUnrated Programs Directions to Block Unrated ProgramsUS V-Chip Ratings Setting US V-Chip Ratings Directions to set US V-Chip RatingsMovies Ratings Directions to set Movie Mpaa RatingsCanadian V-Chip Ratings Directions to set Canadian V-Chip RatingsSet Lock Code Analog Setting LanguageClosed Caption Digital Auto Setting If you want to cancel the settings, select cancelDigital Manual Setting Auto Shut Off Noise MutingFront Panel Lock V3 Smart InputVideo Input Label Position Adjustment Power IndicatorHdmi Size Video-1 AudioDigital Setup Antenna LevelDigital Sound Software VersionSoftware Update Picture Settings Adjust the Picture SettingsColor Temperature Color Management Dynamic GammaAdvanced Smart Picture Natural Cinema Digital VNRReset Mpeg NRSound Settings Adjust the Sound SettingsTurn On Volume Volume LimitSet Clock Thank YOUOn/Off Timer Lamp Timer Reset Following message will appearPower Volume +Number Buttons 10Key Pad TuneDigital/Analog To watch digital channelsMode InputReturn +/TV LightMenu BackFavorite Register the favorite channelDelete the favorite channel Aspect Ratios in PC Mode AspectAspect Ratios Guide By pressing the Aspect button, you can change the sizeSound Sub ChannelTo watch sub channels Video Status Sleep Timer Sleep Timer MessageTwin SwapSelect FreezeDisplay External device control buttonsHow to set the codes Remote programmingSearch Code Function STB mode Programming CodesVCR mode VCR PVR DVD mode Audio mode Weak Signal Invalid SignalNo Program Lamp Message Lamp WarningReplacement Lamp Kit How to Replace the LampTurn off the television Unplug the televisionInstall the new lamp unit Remove the lamp unitPower LED and Lamp LED blink alternately Power LED and Lamp LED blink rapidly simultaneouslyLamp LED blinks Troubleshooting Following are not malfunctions Specifications Specifications subject to change without noticePage Page Page JVC Company of America JVC CANADA, INC