JVC HD-65S998 manual Remove the lamp unit, Install the new lamp unit

Page 80

Lamp Replacement

4) Remove the lamp unit.

Using a Phillips head type screwdriver (cross-head type), loosen the two screws fastening the lamp unit. When the screws have been loosened, remove the lamp by raising the handle and gently sliding the unit towards you. Place it carefully in the recycling packaging.

5) Install the new lamp unit.

Holding the handle attached to the new lamp unit, slide and push the new lamp into the television and back into the lamp housing area. Do not forget to re-tighten the two screws.

Note: If the lamp does not sit securely in the TV (in the lamp housing area), it won’t turn on. Make sure the lamp sits securely in the housing area.

WARNING!

Remember it is very important that YOU DO NOT TOUCH THE LAMP SURFACE. Please read the warnings on page 78 again.

Also, replace the lamp with part number PK-CL120U only! The television is designed to work specifically with this lamp. Lamps other than PK-CL120U may cause malfunctions and/or other damage to the television.

T

NOTICE (for USA)

This product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org

To purchase a replacement lamp kit, please call 1-800-252-5722.

6) Re-install the lamp cover.

Insert the lamp cover in the right concave and close the lamp cover. Because the lamp cover has a role to help prevent the danger of an electrical shock, tighten the screw using a Phillips head type screwdriver (cross-head type).

Notes:

•Make sure the lamp door is closed completely, or the power will not turn on.

•After installing the new lamp unit, do not forget to reset the lamp timer. See page 59.

80

Image 80

Contents Projection Television Users Guide Important Safety Precautions Important Safety Instructions FCC Notice Caring for the Cabinet Caring for the ScreenWhen the power is turned on, the warming up commences Order to use the television for a long timeCooling the inside of the television and the lamp Lamp is a consumable itemTelevision requires a lot of electrical power ILA element characteristicsScreen is made of plastic Do not replace the lamp immediately after useAttaching or removing the pedestals To attach the front and rear pedestalTo remove the front and rear pedestal Table of Contents Quick Setup Unpacking your TVTV Model Side Panel DiagramFront Panel Diagram Remote Control RM-C1400Getting Started Using Menu ButtonsBasic Operation Connecting Your Devices Coaxial CablesVideo Cable Component Cables Composite Cables Audio CablesVCR Connection Diagram #2 Connecting to a Camcorder CamcorderConnecting to an External Amplifier Connecting to an amplifier using your optical outputConnecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT Connecting to the computer Looking at the images from a computerTable of signals for each type of computer When a picture is not displayedLanguage Interactive Plug In MenuAuto Clock Set Manual Clock SetAuto Tuner Setup NOW ProgrammingUsing the Guide Onscreen MenusOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option BlueTo Initial Setup Initial Setup CLOCK/TIMERSAuto Tuner Setup Channel Summary Digital ChannelsContinue to follow these directions for all four spaces Channel Guard Message ChipUnrated Programs Directions to Block Unrated ProgramsUS V-Chip Ratings Setting US V-Chip Ratings Directions to set US V-Chip RatingsMovies Ratings Directions to set Movie Mpaa RatingsCanadian V-Chip Ratings Directions to set Canadian V-Chip RatingsSet Lock Code Closed Caption Analog SettingLanguage Digital Auto Setting If you want to cancel the settings, select cancelDigital Manual Setting Auto Shut Off Noise MutingFront Panel Lock V3 Smart InputVideo Input Label Position Adjustment Power IndicatorHdmi Size Video-1 AudioDigital Setup Antenna LevelDigital Sound Software VersionSoftware Update Color Temperature Picture SettingsAdjust the Picture Settings Advanced Smart Picture Color ManagementDynamic Gamma Natural Cinema Digital VNRReset Mpeg NRSound Settings Adjust the Sound SettingsTurn On Volume Volume LimitSet Clock Thank YOUOn/Off Timer Lamp Timer Reset Following message will appearPower Volume +Number Buttons 10Key Pad TuneDigital/Analog To watch digital channelsMode InputReturn +/TV LightMenu BackDelete the favorite channel FavoriteRegister the favorite channel Aspect Ratios Aspect Ratios in PC ModeAspect Guide By pressing the Aspect button, you can change the sizeTo watch sub channels SoundSub Channel Video Status Sleep Timer Sleep Timer MessageTwin SwapSelect FreezeDisplay External device control buttonsSearch Code Function How to set the codesRemote programming STB mode Programming CodesVCR mode VCR PVR DVD mode Audio mode No Program Weak SignalInvalid Signal Lamp Message Lamp WarningReplacement Lamp Kit How to Replace the LampTurn off the television Unplug the televisionInstall the new lamp unit Remove the lamp unitLamp LED blinks Power LED and Lamp LED blink alternatelyPower LED and Lamp LED blink rapidly simultaneously Troubleshooting Following are not malfunctions Specifications Specifications subject to change without noticePage Page Page JVC Company of America JVC CANADA, INC