JVC HD-65S998 manual Set Lock Code

Page 40

Onscreen Menus

Set Lock Code

Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below.

Press the MENU button

π† To SET LOCK CODE

√® To operate (lock icon appears) Press ZERO to access the lock code

The first digit will be highlighted

√® To select the number

SET LOCK CODE

LOCK CODE	0000

PRESS OK TO FINISH

SELECT OPERATE	MENU EXIT

π† To move to the next digit

Continue to follow these directions for all four numbers

Press the OK button to finish (your lock code is now set)

Press the Menu button when finished

When a viewer attempts to watch a blocked channel, this message appears:

THIS PROGRAMMING EXCEEDS YOUR RATING LIMITS.

PLEASE ENTER LOCK CODE BY 10 KEY PAD TO UNLOCK IT.

NO. - - - -

The channel will remain blocked until the correct lock code is entered (see above for information on setting your lock code).

Notes:

•After a power interruption you must reset the lock code.

•Write your lock code number down and keep it hidden from potential viewers.

•If you forget the lock code, a new code may be set using the steps listed above.

40

Image 40

Contents Projection Television Users Guide Important Safety Precautions Important Safety Instructions FCC Notice Caring for the Cabinet Caring for the ScreenWhen the power is turned on, the warming up commences Order to use the television for a long timeCooling the inside of the television and the lamp Lamp is a consumable itemTelevision requires a lot of electrical power ILA element characteristicsScreen is made of plastic Do not replace the lamp immediately after useAttaching or removing the pedestals To attach the front and rear pedestalTo remove the front and rear pedestal Table of Contents Quick Setup Unpacking your TVFront Panel Diagram Side Panel DiagramTV Model Remote Control RM-C1400Basic Operation Using Menu ButtonsGetting Started Connecting Your Devices Coaxial CablesVideo Cable Component Cables Composite Cables Audio CablesVCR Connection Diagram #2 Connecting to a Camcorder CamcorderConnecting to an External Amplifier Connecting to an amplifier using your optical outputConnecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT Connecting to the computer Looking at the images from a computerTable of signals for each type of computer When a picture is not displayedLanguage Interactive Plug In MenuAuto Clock Set Manual Clock SetAuto Tuner Setup NOW ProgrammingUsing the Guide Onscreen MenusOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option BlueTo Initial Setup Initial Setup CLOCK/TIMERSAuto Tuner Setup Channel Summary Digital ChannelsContinue to follow these directions for all four spaces Channel Guard Message ChipUnrated Programs Directions to Block Unrated ProgramsUS V-Chip Ratings Setting US V-Chip Ratings Directions to set US V-Chip RatingsMovies Ratings Directions to set Movie Mpaa RatingsCanadian V-Chip Ratings Directions to set Canadian V-Chip RatingsSet Lock Code Language Analog SettingClosed Caption Digital Auto Setting If you want to cancel the settings, select cancelDigital Manual Setting Auto Shut Off Noise MutingFront Panel Lock V3 Smart InputVideo Input Label Position Adjustment Power IndicatorHdmi Size Video-1 AudioDigital Setup Antenna LevelDigital Sound Software VersionSoftware Update Adjust the Picture Settings Picture SettingsColor Temperature Dynamic Gamma Color ManagementAdvanced Smart Picture Natural Cinema Digital VNRReset Mpeg NRSound Settings Adjust the Sound SettingsTurn On Volume Volume LimitSet Clock Thank YOUOn/Off Timer Lamp Timer Reset Following message will appearPower Volume +Number Buttons 10Key Pad TuneDigital/Analog To watch digital channelsMode InputReturn +/TV LightMenu BackRegister the favorite channel FavoriteDelete the favorite channel Aspect Aspect Ratios in PC ModeAspect Ratios Guide By pressing the Aspect button, you can change the sizeSub Channel SoundTo watch sub channels Video Status Sleep Timer Sleep Timer MessageTwin SwapSelect FreezeDisplay External device control buttonsRemote programming How to set the codesSearch Code Function STB mode Programming CodesVCR mode VCR PVR DVD mode Audio mode Invalid Signal Weak SignalNo Program Lamp Message Lamp WarningReplacement Lamp Kit How to Replace the LampTurn off the television Unplug the televisionInstall the new lamp unit Remove the lamp unitPower LED and Lamp LED blink rapidly simultaneously Power LED and Lamp LED blink alternatelyLamp LED blinks Troubleshooting Following are not malfunctions Specifications Specifications subject to change without noticePage Page Page JVC Company of America JVC CANADA, INC