JVC HD-65S998 manual Lamp Message, Lamp Warning

Page 78

Lamp Replacement

Lamp Message

LAMP NEEDS TO BE REPLACED. REFER TO OWNER'S MANUAL FOR REPLACEMENT INSTRUCTIONS.

AFTER REPLACING THE LAMP, PLEASE RESET TIMER IN THE TV MENU.

PRESS OK, IF YOU DO NOT WANT TO SEE THIS MESSAGE AGAIN.

If this message appears when you turn the TV on, you need to replace the lamp. See page 79 on how to replace the lamp.

Note:

•This message will appear every time you turn on the TV when the lamp needs to be replaced. Press the OK button to make the message disappear, or replace the lamp.

Lamp Warning

It is very important that you NEVER TOUCH THE NEW LAMP’S GLASS. Dirt or oil from your ﬁngers may cause the lamp to break.

Replace the lamp with part number PK-CL120U only! The television is designed to work specifically with this lamp. Using a different lamp, or a third-party manufacturer’s lamp could cause a malfunction and or damage to the television.

This television uses a 120-Watt high-pressure mercury lamp to project images onto the television screen. When the lamp nears the end of its operating life, you may notice the picture becoming dark. When the picture begins to darken, or the lamp burns out, it is time to replace the lamp. The following instructions will tell you how to safely replace the lamp.

Under operating conditions, THE LAMP WILL GET EXTREMELY HOT AND WILL CAUSE SEVERE BURNS IF TOUCHED.

Before attempting to replace the lamp, make sure the television has completely run through its cooling cycle. Turn the power off and wait until the LAMP LED blinks very slowly and turns off completely. Unplug the TV. If you feel any warmth as you place your hand near the lamp, DO NOT TOUCH IT. Wait until the lamp has completely cooled before attempting to replace it. After turning the power off, wait at least 1 hour or more.

NEVER replace the lamp while the TV is plugged into the wall outlet. Touching the metallic portion of the lamp may cause an electrical shock.

Do not keep the TV on for more than 24 hours consecutively. There is the possibility of the life of the lamp being shortened.

The life of the lamp changes depending on the atmospheric temperature and altitude in which the TV is being used.

Please read these instructions fully before attempting to replace the lamp. If you feel unsure about replacing the lamp yourself, call a service technician.

78

Image 78

Contents Projection Television Users Guide Important Safety Precautions Important Safety Instructions FCC Notice Caring for the Cabinet Caring for the ScreenCooling the inside of the television and the lamp When the power is turned on, the warming up commencesOrder to use the television for a long time Lamp is a consumable itemScreen is made of plastic Television requires a lot of electrical powerILA element characteristics Do not replace the lamp immediately after useAttaching or removing the pedestals To attach the front and rear pedestalTo remove the front and rear pedestal Table of Contents Quick Setup Unpacking your TVSide Panel Diagram Front Panel DiagramTV Model Remote Control RM-C1400Using Menu Buttons Basic OperationGetting Started Video Cable Connecting Your DevicesCoaxial Cables Component Cables Composite Cables Audio CablesVCR Connection Diagram #2 Connecting to a Camcorder CamcorderConnecting to an External Amplifier Connecting to an amplifier using your optical outputConnecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT Connecting to the computer Looking at the images from a computerTable of signals for each type of computer When a picture is not displayedLanguage Interactive Plug In MenuAuto Clock Set Manual Clock SetAuto Tuner Setup NOW ProgrammingUsing the Guide Onscreen MenusSelected Option Green Onscreen Menu SystemOnscreen Menu System Selected Option BlueTo Initial Setup Initial Setup CLOCK/TIMERSAuto Tuner Setup Channel Summary Digital ChannelsContinue to follow these directions for all four spaces Channel Guard Message ChipUnrated Programs Directions to Block Unrated ProgramsUS V-Chip Ratings Setting US V-Chip Ratings Directions to set US V-Chip RatingsMovies Ratings Directions to set Movie Mpaa RatingsCanadian V-Chip Ratings Directions to set Canadian V-Chip RatingsSet Lock Code Analog Setting LanguageClosed Caption Digital Auto Setting If you want to cancel the settings, select cancelDigital Manual Setting Auto Shut Off Noise MutingFront Panel Lock V3 Smart InputVideo Input Label Position Adjustment Power IndicatorHdmi Size Video-1 AudioDigital Setup Antenna LevelDigital Sound Software VersionSoftware Update Picture Settings Adjust the Picture SettingsColor Temperature Color Management Dynamic GammaAdvanced Smart Picture Natural Cinema Digital VNRReset Mpeg NRTurn On Volume Sound SettingsAdjust the Sound Settings Volume LimitSet Clock Thank YOUOn/Off Timer Lamp Timer Reset Following message will appearNumber Buttons 10Key Pad PowerVolume + TuneMode Digital/AnalogTo watch digital channels InputMenu Return +/TVLight BackFavorite Register the favorite channelDelete the favorite channel Aspect Ratios in PC Mode AspectAspect Ratios Guide By pressing the Aspect button, you can change the sizeSound Sub ChannelTo watch sub channels Video Status Sleep Timer Sleep Timer MessageTwin SwapDisplay SelectFreeze External device control buttonsHow to set the codes Remote programmingSearch Code Function STB mode Programming CodesVCR mode VCR PVR DVD mode Audio mode Weak Signal Invalid SignalNo Program Lamp Message Lamp WarningTurn off the television Replacement Lamp KitHow to Replace the Lamp Unplug the televisionInstall the new lamp unit Remove the lamp unitPower LED and Lamp LED blink alternately Power LED and Lamp LED blink rapidly simultaneouslyLamp LED blinks Troubleshooting Following are not malfunctions Specifications Specifications subject to change without noticePage Page Page JVC Company of America JVC CANADA, INC