BenQ W500 Switching input signal, Changing the password, Disabling the password function

Page 25

Changing the password

1.Open the OSD menu and go to the Advanced Setup > Password menu. Press ENTER.

2.Highlight Change Password. Press ENTER.

3.The message 'INPUT CURRENT PASSWORD' displays. Enter the old password.

i.If the password is correct, another message 'INPUT NEW PASSWORD' displays.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT CURRENT PASSWORD' displays for your retry. You can press EXIT to clear and re- enter six digits or go back to the previous page.

4.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.Press EXIT to go back to the previous page, or press MENU to leave the OSD menu.

Disabling the password function

To disable password protection:

1.Go back to the Advanced Setup > Password > Password menu after opening the OSD menu system.

2.Select Off by pressing eLeft orfRight. The message 'INPUT PASSWORD' displays.

3.Enter the current password.

i.If the password is correct, the OSD menu returns to the Password page with 'Off' shown in the row of Password. You will not have to enter the password next time when turning on the projector.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT PASSWORD' displays for your retry. You can press EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple equipment at the same time. However, it can only display one at a time.

• To select an individual input signal, press one of the Source buttons on the remote control.

• To sequentially cycle through all possible sources, press SOURCE on the projector, and the source selection bar displays. Press cUp ordDown repeatedly until your desired signal is selected and press ENTER. If there is multiple equipment connected to the projector, you can press the key again to search for another signal.

Activating automatic source search

Be sure the Auto Source Search in the System Setup menu is activated if you want the projector to automatically search the signals. Go to the System Setup > Auto Source Search menu and select On by pressing eLeft orfRight. The projector will scan for input signals until it acquires a signal. If the function is not activated, the projector selects the last used input signal.

English

Using the projector

25

Image 25
Contents W500 LCD Projector Home Entertainment Series WelcomeTable of contents Speeding up the process of source search MaintenanceMenus Troubleshooting Specifications Warranty and Copyright informationRegulation statements Important safety instructions Important safety instructions Ceiling mounting the projector From the power supplyIntroduction Projector featuresShipping contents Front and upper side Projector exterior viewRear side Under sideProjector Controls and functionsRemote control Remote control effective range Replacing the remote control batteriesChoosing a location Positioning your projectorFloor front Floor rearDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected picture sizeWidescreen ratio screen dimension table Installation for a 169 ratio screenDiagonal Width Height Min Max Highest AverageStandard ratio screen dimension table Installation for a 43 ratio screenDiagonal Width Height Min Lens Feet InchesVertical lens shift Horizontal lens shift Shifting the projection lensConnection Connecting a computerWith a VGA cable With a Hdmi cable Connecting a Hdmi device Connecting Video source devicesTo connect the projector to a Component Video source device Connecting a Component-Video source deviceWith an S-Video cable With a Video cable Connecting an S-video or a composite Video source deviceDevice Video socket on the projectorStart up Using the projectorSetting a password Utilizing the password functionIf you forget the password Entering the password recall procedureChanging the password Switching input signalDisabling the password function Highlight Change Password. Press EnterAdjusting the projection angle Adjusting the projected imageFine-tuning the image size and clarity Correcting two-dimensional keystonePincushion distortion Correcting pincushion and barrel distortionBarrel distortion Using the projector in well lit rooms Selecting a picture modeOptimizing the image Situations as described belowSetting the User 1/User 2/User 3 modes Adjusting picture qualitySelecting the aspect ratio Renaming the User 1/User 2/User 3 modesAdvanced picture quality controls Setting black levelPress eLeft orfRight to select 0 IRE or 7.5 IRE Selecting a color temperature Adjusting picture claritySetting a preferred color temperature Repeat until you are satisfied with the picture clarityColor management Repeat steps 3, 4 and 5 for other color adjustmentsActivating the blue filter Searching for details on the projected image Operating in a high altitude environmentCreating your own startup screen Personalizing the projector menu display Turning the power offOn Screen Display OSD structure MenusFollowing example describes the adjustment of the keystone Using the menusUse Left/ Right to select the Display menu Press Enter and press Up/ Down to select 2D KeystonePicture--Basic menu Display menu Picture--Advanced menuSystem Setup menu Advanced Setup menu Information menu Care of the projector MaintenanceTo clean the filter Calculation of lamp hour Lamp InformationLoosen the screws that hold the lamp to the projector. If Replacing the lampHighlight Reset and press Enter to reset the lamp timer to Indicators Temperature informationIllustration Your dealer for assistance Temp Lamp Thermal eventsProjector does not Turn on TroubleshootingProjector specifications SpecificationsDimensions Hdmi Timing chartRateHz KHz Warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement MIC statement