BenQ W500 user manual Picture--Advanced menu, Display menu

Page 38

English

Picture--Advanced menu

The Picture--Advanced menu allows you to adjust the finer details of the projected image quality.

FUNCTION (default

DESCRIPTION

setting / value)

 

 

 

Black Level (0

See "Setting black level" on page 30 for details.

IRE)

 

 

 

Clarity Control

See "Adjusting picture clarity" on page 31 for details.

 

 

Color Temp.

See "Selecting a color temperature" on page 31 for details.

 

 

Color Temp. Fine

See "Setting a preferred color temperature" on page 31 for details.

Tuning

 

 

 

Color

See "Color management" on page 32 for details.

Management

 

 

 

Dynamic IRIS (On)

Toggles Dynamic IRIS between On and Off.

 

 

Color Space

When using certain European TV setup boxes found with YUV color encoding

system, press eLeft orfRight to select YUV as this will allow images to display

Transfer (Default)

normally.

 

 

Blue Filter (Off)

See "Activating the blue filter" on page 32 for details.

 

 

Display menu

Use this menu to set the way that the projector displays the picture.

FUNCTION (default

DESCRIPTION

setting / value)

 

 

 

Aspect Ratio

There are a few aspect ratios that can be selected for different input signals. See "3.

(Anamorphic)

Selecting the aspect ratio" on page 29 for details.

 

 

 

 

Corrects for trapezoidal distortion resulting from the angle of projection and

 

pincushion distortion of the image.

Keystone (0)

• 2D Keystone (0): Corrects any keystoning of the image. See "Correcting

two-dimensional keystone" on page 26 for details.

 

• Pincushion Correction (0): Corrects any pincushion distortion of the

 

image. See "Correcting pincushion and barrel distortion" on page 27 for

 

details.

 

 

 

Displays the position adjustment page. To move the projected image, use the

 

directional arrow buttons. The values shown on the lower position of the page

Position (0)

change with every button press you made until they reach their maximum or

minimum.

 

 

This function is only available with a D-sub (analog RGB) signal selected.

 

 

Overscan

Slightly magnifies and stretches the picture to remove the less brighter image areas

Adjustment (0)

commonly found towards the four edges.

 

 

 

Digital Zoom

Magnifies the projected image. See "Searching for details on the projected image"

(100%)

on page 33 for details.

 

 

 

38 Menus

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Welcome W500 LCD Projector Home Entertainment SeriesTable of contents Menus MaintenanceSpeeding up the process of source search Regulation statements Warranty and Copyright informationTroubleshooting Specifications Important safety instructions Important safety instructions From the power supply Ceiling mounting the projectorProjector features IntroductionShipping contents Rear side Projector exterior viewFront and upper side Under sideControls and functions ProjectorRemote control Replacing the remote control batteries Remote control effective rangeFloor front Positioning your projectorChoosing a location Floor rearObtaining a preferred projected picture size Determine the aspect ratio of your screen, 169 or 43?Diagonal Width Height Min Max Highest Installation for a 169 ratio screenWidescreen ratio screen dimension table AverageDiagonal Width Height Min Installation for a 43 ratio screenStandard ratio screen dimension table Lens Feet InchesShifting the projection lens Vertical lens shift Horizontal lens shiftWith a VGA cable With a Hdmi cable Connecting a computerConnection Connecting Video source devices Connecting a Hdmi deviceConnecting a Component-Video source device To connect the projector to a Component Video source deviceDevice Connecting an S-video or a composite Video source deviceWith an S-Video cable With a Video cable Video socket on the projectorUsing the projector Start upIf you forget the password Utilizing the password functionSetting a password Entering the password recall procedureDisabling the password function Switching input signalChanging the password Highlight Change Password. Press EnterFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Correcting two-dimensional keystoneBarrel distortion Correcting pincushion and barrel distortionPincushion distortion Optimizing the image Selecting a picture modeUsing the projector in well lit rooms Situations as described belowSelecting the aspect ratio Adjusting picture qualitySetting the User 1/User 2/User 3 modes Renaming the User 1/User 2/User 3 modesPress eLeft orfRight to select 0 IRE or 7.5 IRE Setting black levelAdvanced picture quality controls Setting a preferred color temperature Adjusting picture claritySelecting a color temperature Repeat until you are satisfied with the picture clarityActivating the blue filter Repeat steps 3, 4 and 5 for other color adjustmentsColor management Creating your own startup screen Operating in a high altitude environmentSearching for details on the projected image Turning the power off Personalizing the projector menu displayMenus On Screen Display OSD structureUse Left/ Right to select the Display menu Using the menusFollowing example describes the adjustment of the keystone Press Enter and press Up/ Down to select 2D KeystonePicture--Basic menu Picture--Advanced menu Display menuSystem Setup menu Advanced Setup menu Information menu Maintenance Care of the projectorTo clean the filter Lamp Information Calculation of lamp hourReplacing the lamp Loosen the screws that hold the lamp to the projector. IfHighlight Reset and press Enter to reset the lamp timer to Illustration Temperature informationIndicators Temp Lamp Thermal events Your dealer for assistanceTroubleshooting Projector does not Turn onDimensions SpecificationsProjector specifications Timing chart HdmiRateHz KHz Copyright Warranty and Copyright informationWarranty DisclaimerEEC statement Regulation statementsFCC statement MIC statement
Top Page Image Contents