BenQ CP120C user manual Indicators, Projector needs to cool after the power is Turned off, Process

Page 47

Indicators

Illustration

Blank - : Light OFF

O : Orange light

 

 

 

 

 

 

: Light flashing

R : Red light

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

: Light ON

G : Green light

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Light

Status & Description

 

 

 

 

 

 

 

 

 

 

POWER

TEMPerature

LAMP

 

 

 

 

 

 

 

 

 

 

 

 

Power events

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector needs to cool after the power is

 

 

 

 

 

-

-

 

turned off.

 

 

 

 

 

 

 

O

The projector is in the startup cooling

 

 

 

 

 

 

 

 

process.

 

 

Stand-by mode.

O

-

-

 

 

 

 

 

-

-

The Power indicator light is flashing during

 

G

 

powering up.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector is under normal operation.

G

-

-

Lamp events

 

-

 

It is warning you that lamp usage has exceeded

O

R

2000 / 3000 (Economic mode) hours. Replace the

 

 

 

projection lamp with a new one immediately.

-

-

 

 

 

 

 

The lamp is not properly attached or the lamp is

 

R

 

damaged. Please contact your dealer for assistance.

 

 

 

 

 

 

 

 

 

 

Thermal events

-

 

 

 

-

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-

 

 

 

 

 

 

R

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-

 

 

 

 

 

R

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance.

Maintenance 41

Image 47
Contents Welcome Disclaimer CopyrightTable of Contents Iv Table of Contents Fine-tuning the image size and clarityTable of Contents Memo Vi Table of Contents Important safety instructions Important safety instructionsBut could fail if power cuts or surges Safety instructions Other item Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Bedding or any other soft surfaceSafety instructions Introduction Projector featuresIntroduction Shipping contents Lower side Projector exterior viewFront / Upper side Rear sideTurns the projector on or off Controls and functionsExternal control panel Selects one of the application modes Adjusts the focus of the projected imageFreeze button Remote control descriptionInstalling or replacing the remote control battery Remote control effective rangeEquipment Positioning your projectorChoosing a location Obtaining a preferred projected image sizeSelect your screen size Positioning your projector Screen Center of lens Projection distance Screen size chartMaximum Minimum Zoom Connection Connecting a computerConnection Best video quality Connecting Video source devicesComponent Video to VGA D-Sub adaptor cable Device Connecting a Component Video source deviceVideo cable Device Connecting an S-Video source deviceConnecting a composite Video source device Start up Using the projectorUsing the projector If you forget the password Utilizing the password functionTo set a password To change the password Adjusting the heightTo enter the password recall procedure Correcting keystone Auto-adjusting the imageFine-tuning the image size and clarity That you need using the zoom ring Focus ringAutomatic keystone correction Selecting an application modeBrightest Presentation Default SRGB/Photo Gaming Video Movie default Cinema Photo Gaming Using the projectorFreezing the image Switching input signalHiding the image Remote paging operationsShutdown Disconnect the power cord from the wall socketMenu system Menu operationUsing the menus Picture menu Depends on Selected Application ModeKeystone Color TempPro-Picture menu Setting menu Advance menu Periods of time 10hours without shutdown Turned off. Selecting Off disables this functionAuto Off Off EconomicSource ResolutionMode Equivalent Information MenuCare of the projector MaintenanceMessage Status Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature informationPowering up IndicatorsProjector needs to cool after the power is Turned off Stand-by modeMaintenance Image is unstable TroubleshootingProjector does not turn on No pictureRemote control does not work Projector specifications SpecificationsSupported timing for PC input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for Video and S-Video inputs Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Component-YPbPrInput Warranty WarrantyLimited warranty Ices Statement Canada Regulation statementsFCC statement EEC statementMemo Regulation statements