BenQ CP120C user manual Regulation statements, FCC statement, EEC statement, Ices Statement Canada

Page 55

Regulation statements

FCC statement

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

EEC statement

Here by, BenQ Corporation, declares that the product is in compliance with the essential requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating CE-Mark Directive (93/68/EEC), Electromagnetic Compatibility Directives (89/336/EEC, 92/31/EEC) and Low Voltage Directive (73/23/EEC).

ICES Statement (Canada)

This Class B digital apparatus complies with Canadian ICES-003.

VCCI Statement

MIC statement

B class equipment (Household purpose info/telecommunications equipment)

As this equipment has undergone EMC registration for household purpose, this product can

be used in any area including residential area.

Regulation statements

49

Image 55
Contents Welcome Disclaimer CopyrightTable of Contents Iv Table of Contents Fine-tuning the image size and clarityTable of Contents Memo Vi Table of Contents But could fail if power cuts or surges Important safety instructionsImportant safety instructions Safety instructions Other item Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Bedding or any other soft surfaceSafety instructions Introduction Projector featuresIntroduction Shipping contents Lower side Projector exterior viewFront / Upper side Rear sideExternal control panel Controls and functionsTurns the projector on or off Selects one of the application modes Adjusts the focus of the projected imageFreeze button Remote control descriptionInstalling or replacing the remote control battery Remote control effective rangeEquipment Positioning your projectorChoosing a location Obtaining a preferred projected image sizeSelect your screen size Positioning your projector Maximum Minimum Zoom Screen size chartScreen Center of lens Projection distance Connection Connecting a computerConnection Best video quality Connecting Video source devicesComponent Video to VGA D-Sub adaptor cable Device Connecting a Component Video source deviceVideo cable Device Connecting an S-Video source deviceConnecting a composite Video source device Using the projector Using the projectorStart up To set a password Utilizing the password functionIf you forget the password To enter the password recall procedure Adjusting the heightTo change the password Correcting keystone Auto-adjusting the imageFine-tuning the image size and clarity That you need using the zoom ring Focus ringAutomatic keystone correction Selecting an application modeBrightest Presentation Default SRGB/Photo Gaming Video Movie default Cinema Photo Gaming Using the projectorFreezing the image Switching input signalHiding the image Remote paging operationsShutdown Disconnect the power cord from the wall socketMenu system Menu operationUsing the menus Picture menu Depends on Selected Application ModeKeystone Color TempPro-Picture menu Setting menu Advance menu Periods of time 10hours without shutdown Turned off. Selecting Off disables this functionAuto Off Off EconomicSource ResolutionMode Equivalent Information MenuCare of the projector MaintenanceMessage Status Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature informationPowering up IndicatorsProjector needs to cool after the power is Turned off Stand-by modeMaintenance Image is unstable TroubleshootingProjector does not turn on No pictureRemote control does not work Projector specifications SpecificationsSupported timing for PC input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for Component-YPbPrInput Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Video and S-Video inputs Limited warranty WarrantyWarranty Ices Statement Canada Regulation statementsFCC statement EEC statementMemo Regulation statements