BenQ CP120C Adjusts the focus of the projected image, Selects one of the application modes

Page 15

6.Keystone /3Left button (Refer to "Correcting keystone" on page 24 and "Using the menus" on page 29 for more information)

Press this button to correct keystoning at the top of the projected image.

When the on-screen menu is activated, press this button to move the selection focus left or make adjustments.

7.SOURCE button (Refer to "Switching input signal" on page 26 for more information) Switches sequentially through input sources. (RGB/YPbPr, Video or S-Video).

8.MENU /6Down button (Refer to "Using the menus" on page 29 for more informa- tion)

Turns on the On-Screen Display (OSD) menu.

When the on-screen menu is activated, press this button to move the selection focus down.

9.Focus ring (Refer to "Fine-tuning the image size and clarity" on page 24 for more information)

Adjusts the focus of the projected image.

10.LAMP indicator light (Refer to "Indicators" on page 41 for more information)

Lights up or flashes when the projector lamp has developed a problem.

11.MODE button (Refer to "Selecting an application mode" on page 25 for more infor- mation)

Selects one of the application modes.

12.Keystone /4Right button (Refer to "Correcting keystone" on page 24 and "Using the menus" on page 29 for more information)

Press this button to correct keystoning at the bottom of the projected image.

When the on-screen menu is activated, press this button to move the selection focus right or make adjustments.

13.AUTO button (Refer to "Auto-adjusting the image" on page 24 for more information)

Press this button to let the projector automatically determine the best picture timings for the projected image.

Introduction 9

Image 15

Contents Welcome Disclaimer CopyrightTable of Contents Iv Table of Contents Fine-tuning the image size and clarityTable of Contents Memo Vi Table of Contents Important safety instructions But could fail if power cuts or surgesImportant safety instructions Safety instructions Other item Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Bedding or any other soft surfaceSafety instructions Projector features IntroductionIntroduction Shipping contents Lower side Projector exterior viewFront / Upper side Rear sideControls and functions External control panelTurns the projector on or off Selects one of the application modes Adjusts the focus of the projected imageFreeze button Remote control descriptionInstalling or replacing the remote control battery Remote control effective rangeEquipment Positioning your projectorChoosing a location Obtaining a preferred projected image sizeSelect your screen size Positioning your projector Screen size chart Maximum Minimum ZoomScreen Center of lens Projection distance Connecting a computer ConnectionConnection Best video quality Connecting Video source devicesComponent Video to VGA D-Sub adaptor cable Device Connecting a Component Video source deviceVideo cable Device Connecting an S-Video source deviceConnecting a composite Video source device Using the projector Using the projectorStart up Utilizing the password function To set a passwordIf you forget the password Adjusting the height To enter the password recall procedureTo change the password Correcting keystone Auto-adjusting the imageFine-tuning the image size and clarity That you need using the zoom ring Focus ringAutomatic keystone correction Selecting an application modeBrightest Presentation Default SRGB/Photo Gaming Video Movie default Cinema Photo Gaming Using the projectorFreezing the image Switching input signalHiding the image Remote paging operationsShutdown Disconnect the power cord from the wall socketMenu system Menu operationUsing the menus Picture menu Depends on Selected Application ModeKeystone Color TempPro-Picture menu Setting menu Advance menu Periods of time 10hours without shutdown Turned off. Selecting Off disables this functionAuto Off Off EconomicSource ResolutionMode Equivalent Information MenuCare of the projector MaintenanceMessage Status Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature informationPowering up IndicatorsProjector needs to cool after the power is Turned off Stand-by modeMaintenance Image is unstable TroubleshootingProjector does not turn on No pictureRemote control does not work Projector specifications SpecificationsSupported timing for PC input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSignal Format Horizontal Frequency Vertical Frequency KHz Supported timing for Component-YPbPrInputSupported timing for Video and S-Video inputs Warranty Limited warrantyWarranty Ices Statement Canada Regulation statementsFCC statement EEC statementMemo Regulation statements