BenQ CP120C user manual Selecting an application mode, Automatic keystone correction

Page 31

Keystone /3Left button to correct keystoning at the top of the image. Press the

Keystone /4Right button to correct keystoning at the bottom of the image.

Press the / buttons on the remote control to display the status bar labelled

Keystone, then press the button to correct keystoning at the top of the image or

press the button to correct keystoning at the bottom of the image.

Press the MENU/6Down button on the projector or the MENU button on the remote

control. Go to Picture --> Keystone and adjust the values by pressing the

Keystone /3Left or Keystone /4Right buttons on the projector, or the

3Left or 4Right buttons on the remote control. For example,

Keystone 0

Keystone

1.Press the Keystone /3Left button on the projector or

2.Press the button on the remote control or

3.Press the Keystone /3Left button on the projector, or the3Left button on the remote control when you are in the Picture --> Keystone menu.

1.Press the Keystone /Right 4 button on the projector or

2.Press the button on the remote control or

3.Press the Keystone /Right 4button

0on the projector, or the 4 Right button on the remote control when you are in the Picture --> Keystone menu.

Keystone

Keystone

-6

+6

Automatic keystone correction

Your projector is equipped with Autokeystone function that corrects keystoning automatically. See "Autokeystone (On)" on page 30 for details.

Selecting an application mode

The projector is preset with several predefined application modes so that you can choose one to suit your operating environment and input source picture type. To select a operation mode that suits your need, press the MODE button. The application modes available for

different types of signals are shown below. See "Application Mode" on page 30 for details.

PC Signal Input

Brightest

Presentation

(default)

sRGB/Photo

Gaming

Video

YPbPr / S-Video / Video Signal Input

Movie (default)

Cinema

Photo

Gaming

Using the projector

25

Image 31
Contents Welcome Disclaimer CopyrightTable of Contents Iv Table of Contents Fine-tuning the image size and clarityTable of Contents Memo Vi Table of Contents But could fail if power cuts or surges Important safety instructionsImportant safety instructions Safety instructions Other item Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Bedding or any other soft surfaceSafety instructions Introduction Projector featuresIntroduction Shipping contents Lower side Projector exterior viewFront / Upper side Rear sideExternal control panel Controls and functionsTurns the projector on or off Selects one of the application modes Adjusts the focus of the projected imageFreeze button Remote control descriptionInstalling or replacing the remote control battery Remote control effective rangeEquipment Positioning your projectorChoosing a location Obtaining a preferred projected image sizeSelect your screen size Positioning your projector Maximum Minimum Zoom Screen size chartScreen Center of lens Projection distance Connection Connecting a computerConnection Best video quality Connecting Video source devicesComponent Video to VGA D-Sub adaptor cable Device Connecting a Component Video source deviceVideo cable Device Connecting an S-Video source deviceConnecting a composite Video source device Using the projector Using the projectorStart up To set a password Utilizing the password functionIf you forget the password To enter the password recall procedure Adjusting the heightTo change the password Correcting keystone Auto-adjusting the imageFine-tuning the image size and clarity That you need using the zoom ring Focus ringAutomatic keystone correction Selecting an application modeBrightest Presentation Default SRGB/Photo Gaming Video Movie default Cinema Photo Gaming Using the projectorFreezing the image Switching input signalHiding the image Remote paging operationsShutdown Disconnect the power cord from the wall socketMenu system Menu operationUsing the menus Picture menu Depends on Selected Application ModeKeystone Color TempPro-Picture menu Setting menu Advance menu Periods of time 10hours without shutdown Turned off. Selecting Off disables this functionAuto Off Off EconomicSource ResolutionMode Equivalent Information MenuCare of the projector MaintenanceMessage Status Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature informationPowering up IndicatorsProjector needs to cool after the power is Turned off Stand-by modeMaintenance Image is unstable TroubleshootingProjector does not turn on No pictureRemote control does not work Projector specifications SpecificationsSupported timing for PC input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for Component-YPbPrInput Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Video and S-Video inputs Limited warranty WarrantyWarranty Ices Statement Canada Regulation statementsFCC statement EEC statementMemo Regulation statements