Maxtor 4Channel Stand-alone DVMR manual Record Setup, Record Configuration, Multiplex, Super Fine

Page 28

CHAP. 5 Set Up

5-4. RECORD SETUP

This is the most important configuration of the DVR. Enter into SYSTEM MENU-RECORD SETUP and press the [ENTER] button.

1) RECORD CONFIGURATION

Use direction button to move and [-] [+] button to set value.

(1)OVERWRITE : Set overwrite or stop recording when the HDD is full.

(2)MULTIPLEX

-DUPLEX : Playback & Ethernet

-TRIPLEX : Playback & Recording & Ethernet

Note: DUPLEX MODE is recommended to playback the images at a maximum frame rate.

But, it makes DVR not to record during search.

RECORD SETUP

RECORD CONFIGURATION

SCHEDULE SETUP

HOLIDAY SETUP

SELECT MENU : ▲▼, & [ENTER]

(3) QUALITY : Set recording picture quality.

Actually it is fixing maximum data size of image for each picture quality in 5 steps as follows.

-BASIC

-NORMAL

-ENHANCED

-FINE

-SUPER FINE: Default quality set by manufacturer

In Emergency recording mode, recording quality is

SUPER FINE.

RECORD CONFIGURATION

OVERWRITE

ON

MULTIPLEX

TRIPLEX

QUALITY

ENHANCED

RESOLUTION

60IPS 720*240

RECORD IN ALARM

1/1X

RECORD IN MOTION

1/1X

CONTINUOUS RECORD

1/1X

 

 

SELECT MENU : ▲▼, CHANGE VALUE : + -

To send more images via IP network and longer recording time, set QUALITY at NORNAL or ENHANCED and record at 360x240 or 360x120.

Data size of image in PAL system is a little bigger than NTSC system, but the total recording time is same as in NTSC system.

(4)RESOLUTION : Set recording resolution.

- 60 ips at 720x240(NTSC) , 50 ips at 720x288(PAL)

-120 ips at 360x240(NTSC) , 100 ips at 360x288(PAL)

-240 ips at 360x120(NTSC) , 200 ips at 360x144(PAL)

Images recorded in 360x240(360x288) or 360x120(360x144) are always played in quad mode. It is not possible to see those images in full screen mode in playback.

Recording in half or quad resolution is recommended for higher recoding speed, and also to send more images via IP network.

(5)RECORD IN ALARM : Set record speed (skip rate) in ALARM record mode.

(6)RECORD IN MOTION : Set record speed (skip rate) in MOTION record mode.

(7)CONTINUOUS RECORD : Set record speed (skip rate) in CONTINUOUS record mode.

Set record speed (skip rate)

- 1/1x, 1/2x, ………. 1/999x record speed

- ex: 1/2x ) R->S->R->S…- ex: 1/3x ) R->S->S->R->S->S->R…

- ex: 1/4x ) R->S->S->S->R->S->S… ( R : RECORD S : SKIP )

- ex : If record resolution is set at 360x240, 1/1x = 120 ips, 1/2x = 60 ips, 1/3x = 40 ips, etc.

27

Image 28
Contents 4Channel Stand-alone Dvmr Environment Condition for Installation Installation & SafeguardsBefore You Start Contents PTZ Camera Operation Data Back-Up Chap Features & Package Contents Package Contents On Light on SET SET Preset ⑥ Setup MenuFAR Focus FAR Wide ZoomPTZ ZoomFRZ ModePower SwitchVGA EthernetCHAP.3 Installation Installation ConfigurationDetailed Installation Rack mount HDDCamera PowerMonitor VCR, Video Printer Other External DeviceRS-232C ASCII-code Connector Pin Assignment DescriptionJog / Shuttle System Menu Configuration Password Setup Factory DefaultFactory Default System Log-InDisplay Configuration Live View SetupInterval Setup ※ While entered in the Menu Search Search BAR SearchTIME/DATE Event List PAN/TILT/ZOOM Camera Operation CD-R SetupFunction Entering into the Menu DownLeft RightDisplay Setup Monitor SetupDisplay Setup Screen DisplayConfiguration HDD ManagementTIME/DATE Setup Camera SetupMotion Setup Highlighted AreaMotion Detection Area Non-highlighted AreaInterval Setup Alarm SetupInterval Setup Alarm SetupPassword Setup Buzzer SetupSystem Information Record Setup Record ConfigurationMultiplex Super FineSchedule Setup Schedule SetupHoliday Setup Schedule REC SetupTCP/IP Setup IP Config SetupIP Config Setup BACK-UPRS-232C Setup Connection SetupPAN/TILT Setup Language Setup Factory DefaultFactory Default DVR Network Configuration PC’s TCP/IP SettingConfigure the DVR as follows Accessing the DVR using the Remote Software for Case aCase a Single Static IP w/Personal Router DVRAccessing the DVR using the Remote Software for Case B RemotelyCase B Single Static IP Directly Connected to the DVR ISPCase C Dynamic or PPPoE IP w/Personal Router Accessing the DVR using the Remote Software for Case C Case D Multiple Static IPs w/Personal RouterAccessing the DVR using the Remote Software for Case D Accessing the DVR using the Remote Software for Case E Remote Viewer program Setting, Playback, and Sequence buttonsMain Interface Setting Screen Playback Interface through Remote Viewer Chap Network Setup Chap Network Setup Function button Back-up CD PlayerScreen division 1/4/9/16 Image Edit How do I choose a unique IP that matches my network? How do I Ping an IP address ?How do I open an MS-DOS or Command Prompt ? Why is my remote video jerky? How do I forward a port in my router?Chap Specifications Memo Best Picture Quality JPEG2000