Philips DVD963SA manual Basic Engine

Page 12

EN 26

 

5.

 

DVD963SA

Diagnostic Software, Trouble Shooting and Test Instructions

5.5Basic Engine

5.5.1Version Number

In the basic engine tests, the version number of the Basic Engine will be shown first, as the following example:

CL 16532162_043.eps 080102

Figure 5-25

CL 16532162_040.eps 080102

Figure 5-22

By pressing the PLAY key, the Basic Engine tests are started.

5.5.2Tray Test

First, the tray is tested. The purpose of this test is also to give the user the opportunity to put a disc in the tray of the DVD player. Some tests on the Basic Engine require that a disc (e.g. DVD MPTD test disc) is present in the player. At the end of the Basic Engine tests this tray test will be repeated solely to enable the user to remove the disc in the tray.

The local display will look as follows:

By pressing OPEN/CLOSE the user confirms that the disc motor is running. Pressing STOP indicates the disc motor does not work. Pressing PLAY proceeds to the next test, after a reset of the disc motor (nucleus BeDiscMotorOff). If the user presses PLAY before pressing OPEN/CLOSE or STOP, the result of this test will be TRUE (disc motor is running).

5.5.5Focus Test (Visual Test)

The fourth Basic Engine test tests the focussing. First focussing is turned on by calling nucleus BeFocusOn. The display will look as follows:

CL 16532162_044.eps 080102

Figure 5-26

CL 16532162_041.eps 080102

Figure 5-23

By pressing OPEN/CLOSE the user can toggle the position of the tray. Note that this test will not contribute to the test result of the Basic Engine. Pressing PLAY will proceed to the next test. At this point, the tray will be closed automatically by the software if it was open.

5.5.3Sledge Test (Visual Test)

The second Basic Engine test tests the sledge. The user can move the sledge as many times as desired by using OPEN/ CLOSE (nucleus BeSledgeOut) and STOP (nucleus BeSledgeIn). Pressing PLAY on the local keyboard proceeds to the next test. Note that this test will not contribute to the test result of the Basic Engine.

The local display will look as follows during the sledge test:

CL 165321625_042.eps 080102

Figure 5-24

5.5.4Disc Motor Test (Visual Test)

The third Basic Engine test tests the disc motor (nucleus BeDiscMotorOn).

The local display looks as follows:

By pressing OPEN/CLOSE the user confirms that the focussing was succesful. Pressing STOP indicates a focussing failure. Pressing PLAY proceeds to the next test after a reset of the focussing (nucleus BeFocusOff). If PLAY is pressed before OPEN/CLOSE or STOP, the result of this test will be TRUE (focus successful).

5.5.6Radial Test (Visual & Listening Test)

The fifth Basic Engine test tests the radial functionality (nucleus BeRadialOn).

The local display looks as follows:

CL 16532162_045.eps 080102

Figure 5-27

By pressing OPEN/CLOSE the user confirms that the radial function works.Pressing STOP indicates the function does not work. Pressing PLAY proceeds to the next test, after a reset of the radial (nucleus BeRadialOff). If the user presses PLAY before pressing OPEN/CLOSE or STOP, the result of this test will be TRUE (radial successful).

5.5.7Jump Test (Listening Test)

The sixth and last Basic Engine test tests the jumping by calling nuclei BeGroovesIn, BeGroovesMid and BeGroovesOut. During this test, the local display looks as follows:

Image 12
Contents Contents DVD-Video PlayerDVD963SA /001 /171 /691 Specifications Technical Specifications and Connection FacilitiesSafety Instructions, Warnings and Notes Safety InstructionsLaser Device Unit DolbyService Hints MechanicalInstructions Exploded View Exploded ViewService Hints Switched Mode Power SupplyService Positions ComPairDiagnostic Software, Trouble Shooting and Test Instructions Nucleus Contents of Dealer ScriptDealerscript Purpose of Dealer ScriptContents of Player Script Player ScriptPurpose of Player Script Survey Structure of Player ScriptRemote Control Test Display PCBDisplay Test LED Test162037.eps 5 P50 Loop-Back TestDiagnostic Software, Trouble Shooting and Test Instructions Mono PCB Digital PartTest can be left by pressing the Play key for more than One second Picture Test Sound 2 TestBasic Engine Error Log See Table on Error BitsLoop Test See Table Below Uart Error Codes Be ErrorsSlph Error Codes SSM Error CodesSMA Error Codes Reprogramming of New Mono BoardsMenu and Command Mode Interface Command Overview of NucleiSet-up Physical Interface Components Hardware required ActivationProcessor and peripherals Ref. # Reference Name Remark Components Ref. # Reference Name RemarkAudio Ref. # Reference Name Remark Ref. # Reference Name RemarkLayout of Menu and Submenu MenusFirst Level Submenus Second Level SubmenusNuclei Error Codes Audio Nuclei Error Error text CodeThird Level Submenus Error Error text Code Basic Engine Nuclei Error Code Error textError Code Error text Display PWB Nuclei Error Code Error text Processor & Peripherals Nuclei Error Code Error textLog Nuclei Error Code Error text Miscellaneous Nuclei Error Code Error textVideo Nuclei Error Error text Code Test Instruction Front Display and Audio/ Video Board Supply CheckClock Check Audio Mute CheckRef.# Command Name Remarks Audio output Ref.# Command Name RemarksCommand Ref.# Name Remarks Audio output Command Ref.# Name Remarks Killlr signalPersonal Notes Block and Wiring Diagram Block Diagram DVD963SAScart Switch Wiring Diagram DVD963SATestpoint Overview A/V Board Testpoint Overview Display Panel Testpoint OverviewP-Scan Board Electrical Diagrams Power Supply Unit DVD963SASYS CLK & Control AV-Board Clock & ControlUpsampling AV-Board UpsamplingAudio DAC Current to Voltage Converter AV-Board Current to Voltage ConverterAV Audio AV-Board AudioAV Video and Scart AV-Board Video and ScartLayout AV-Board Top Side Layout AV-Board Overview Bottom Side Layout AV-Board Part 1 Bottom Side Layout AV-Board Part 2 Bottom Side Display Panel Display PanelLayout Display Panel Top Side Layout Display Panel Overview Bottom Side Part Layout Display Panel Part 1 Bottom SidePart Layout Display Panel Part 2 Bottom SideScanLineDoubler Scan Board Line DoublerScanE ncoder Scan Board Video Output 1003-B C9Layout P-Scan Board Overview Top Side PartLayout P-Scan Board Part 1 Top Side Layout P-Scan Board Part 2 Top Side Layout P-Scan Board Overview Bottom Side Layout P-Scan Board Part 1 Bottom Side Layout P-Scan Board Part 2 Bottom Side Standby Board Layout Standby Board Top SideLayout Standby Board Bottom Side Switching Double Scart Panel Switching Only for EU modelsScart Part CL1653200795a.eps CL1653200795b.eps Layout Double Scart panel Only for EU models Part 1 Top Side Layout Double Scart panel Only for EU models Part 2 Top Side Power Supply Unit AlignmentsCircuit Descriptions and List of Abbreviations IntroductionLoader/Mono Board for diagrams see Primary Current SensingUnder-voltage Protection Over-voltage ProtectionLoader Interface Servo Processor/DecoderInterface/Program Memory Back-end the Digital PartSacd DSD processor Basic Engine InterfaceAudio data input/output Interface Audio Output Video OutputPower Supply diagram M7 Clock FactoryMiscellaneous Reset Circuit Audio/Video A/V BoardProgressive Scan Board Double ScartDVD Player VCR/STB/etcControl and Display Panel Abbreviation list ASDDiagram Power Supply TY72011P2 item IC DataDiagram A2 AK4103VF IC7203 16 AK4103VF IC7203Diagram A3 CS4362 IC7300 17 CS4362 IC7300Diagram P1 FLI2301 item 18 FLI2301 itemSpare Parts List Mechanical /001SD4.00SA Module Mechanical /171RC22H Front PWB IC SM 74LVC04ADB PhseSpare Parts List Scan PWBScart PWB Errata Revision ListManual 3122 785
Related manuals
Manual 2 pages 34.61 Kb