Philips 64PH9901 manual Safety Instructions Read before operating equipment

Page 3

SAFETY INSTRUCTIONS - Read before operating equipment

This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.

1.Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions - The safety and operating instructions should be retained for future reference.

3.Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions - All operating and use instructions should be followed.

5.Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool, etc.

6.Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A.An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination

to overturn.

6B. Tilt/Stability - All televisions must comply with recommended international global safety standards for tilt and stability properties of its cabinet design.

•Do not compromise these design standards by applying exces- sive pull force to the front, or top, of the cabinet which could ultimately overturn the product.

•Also, do not endanger yourself, or children, by placing elec- tronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.

7.Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

8.Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9.Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10.Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

11.Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

12.Cleaning - The appliance should be cleaned only as recommended by the manufacturer.

13.Power Lines - An outdoor antenna should be located away from power lines.

14.Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mats and supporting structure grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding electrode. See Fig. below.

15.Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

16.Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

17.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A.The power supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

18.Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding

as per NEC - National Electric Code

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 64PH9901 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cleaning and care of the DptvAs you unpack your Dptv please note that Press CHannel and VOLume + on the DPTV’s Ntsc Analog ON-SCREEN Menu FeaturesFirst Time Setup First Time Setup automatically takesCOLOR, Brightness SHARPNESS, TINT, Picture Ntsc Analog Picture Menu ControlsPress the exit button to clear ClearviewSelect Clearview control Press the Menu buttonsPress the Menu buttons Ntsc Analog Picture Menu ControlsRED/BLUE Convergence Select ConvergenceSmart Picture Ntsc Analog Feature Menu ControlsNtsc Analog Feature Menu Controls Smart PictureChange Label Text 1, 2, 3 Closed CaptionSelect Closed Captioning control Caption 1, 2, 3Cable TV connected Cable TuningSelect Cable Channel CABLE- If you do haveChannel buttons Channel Memory AUTO-PROGRAMMINGSelect Channel Memory Press the exit or MenuPress the Menu button to ADD/DELETE ChannelsSelect Channel Memory Press the Channel +Press the remotes number SET ClockPressed Select SET Clock controlChannel Display Select Channel DisplayPress the Menu Menu M buttons to highlight See instruction details on this Channel LabelsDo you ever have trouble Remembering on which Select Channel Labels controlPress the Menu arrow Ntsc Analog Sound Menu ControlsBASS, TREBLE, Balance Select BASS, or TREBLE, orSecond Audio Program SAP StereoSelect Stereo sound control Second Audio ProgramPress the Menu Menu M buttons to highlight Display VolumeSelect Display Volume Ntsc Analog Sound Menu ControlsCommercial breaks Automatic Volume LimiterGently tap the Pronto Pronto Remote Ntsc Analog FeaturesPronto Analog TV Mode Refer to the 64PP9901 Quick UseAUDIO/VIDEO Ntsc Analog Connections AUX1/2 InputsConnect the Video OUT jack AUX Ntsc AUX 3 InputsAUX1 S-VIDEO Inputs Connect the S-VIDEO STurn the VCR on and place it Press the ext input button Audio /VIDEO Ntsc Analog ConnectionsAUDIO/VIDEO Outputs Connect the Audio OUTConnect the Right and Left System Audio OUT jacks on System Audio OutputsPress the exit or Menu button to clear the screen Atsc Digital ON-SCREEN Menu FeaturesDTV Setup Autoprogram Select DTV Setup controlAtsc Digital Picture Menu Controls With Picture Menu on-screen Screen when convergence Adjustments are completeAtsc Digital Picture Menu Controls Select the Atsc ConvergencePlace the speakers so Atsc Digital Sound Menu ControlsSurround Sound Connect both externalAtsc Digital Sound Menu Controls Surround SoundDolby Digital Surround Dolby Digital Surround Additional Connections Select Bass or Treble sound Auto VolumeSelect Auto Volume sound BASS, TrebleMenu Atsc Digital Speakers Menu ControlsSpeakers Select the Atsc SpeakersPress the Menu arrow Test ToneControl is turned On Select Test Tone sound controlButtons to select the Captions Atsc Digital Features Menu ControlsSelect the Atsc Features Menu Captions FormatPress the Menum Atsc Digital Features Menu ControlsSelect the Atsc Features Menu ADD/DELETE ChannelPronto Remote Atsc Digital Features Pronto Digital TV ModeOther details on the initial use Pronto remote control also Cable optional from the VGA Monitor Features Menu ControlsConnect a 15 pin VGA signal VGA/SVGA/HDCOMPONENTPress the Left/Right Press the exit button to clear the screen when completeMonitor Menu Controls ReplayDptv Displays Wrong Channel or incorrect program Tips if Something Isnt WorkingIndex Glossary to Television Terms Philips Consumer Electronics Company Georgia Texas Illinois Limited Warranty
Top Page Image Contents