Philips 26HW9100D, 30HW9100D user manual TV Setup Menu and Sub-Menus

Page 11

L05 User’s Manual

091105.1833

TV Setup Menu and Sub-Menus

LANGUAGE(English / Espanol / Francais)

When you first enter the TV SETUP menu, LANGUAGE is highlighted. You can scroll to the LANGUAGE item. Select the desired language with cursor up / cursor down.

CHANNEL INSTALL

(>)

The CANNEL INSTALL menu allows the user to configure the channels that can be accessed. When installing the channels, different inputs can be mapped to TV channels to allow seamless integration into the channel map. The two sections below explain how to install analog channels and AV inputs, and how to install digital channels.

Installing Analog channels

When selected, CHANNEL INSTALL menu appears as follows. Configure the inputs and channels as described.

 

CHANNEL INSTALL

CHANNEL

TV 1 – 125

INPUT

ANTENNA / AV 1 / AV 2 / SIDE / S-VIDEO / CVI / AV3YC /

 

HDMI / HD CVI / DIGITAL

AUTO PROGRAM

>

CHANNEL RING

SAVED

LABEL

>

VIDEO BLANK

 

AUDIO MUTE

 

 

 

CHANNEL:

oSelect the channel or input you wish to configure.

INPUT:

oSelect the input source that you wish to associate with the specified CHANNEL . This feature enables you to “map” (re-assign) a numeric channel number to a video input, rather than to its normal RF TV channel (i.e. ANTENNA). In other words, TV channel 2 could be used to select the AV 1 video input instead of RF (ANTENNA) channel 2. Special ins tructions for mapping digital channels are included below.

AUTO PROGRAM:

oWhen AUTO PROGRAM is selected, the TV performs an automatic search for the presence of viable RF signals at its tuner input. An AUTO- PROGRAMMING ACTIVE message and a table of channe l numbers will appear. If CABLE TUNING is set to NO, channels 2 through 69 will be checked. If CABLE TUNING is set to YES, channels 2 through 125 will be checked. When a viable signal is detected on a given channel, that channel is highlighted in red and is added to the channel ring. Any command from a remote control terminates the AUTO PROGRAM session. Front-panel commands do not cancel auto-programming.

CHANNEL RING:

11

Image 11
Contents 26HW9100D/30HW9100D User’s Manual Safety Information Symptom Possible Corrective Action Before Calling ServiceBasic Television Connection Rear Jack Panel Connections Use And Care of Remote ControlRemote Controls DVD Stop Guest Remote Control KeysAccessing TV Setup Menus Consumer vs. Commercial ModePage TV Setup Main Menu TV Setup Menu and Sub-Menus ∙ Audio Mute Installing AV Inputs∙ Label ∙ Video Blank∙ Minor Channel Factory CH ResetCursor Right will reset the channels programmed in memory ∙ Major ChannelCursor Right will bring up the Consumer Digital Menu below USE Channel Table NO/YESDigital OSDNO/YES Enter Digital MenuContrast Default FormatBrightness ColorNoise Reductionno / YES Using the different formatsBalance Sound Mode Mono / StereoVolume BAR Avloff / onChannel Displaynone / Number / Label / ALL MAX VolumeSwitch on Volumestandard / 0 Power Onstandard / Forced /RESTOREDMonitor OUT Rfno / YES ESPAUDIO/VIDEO Muteoff / Black / Blue AUDIO/VIDEO OUT Mute∙ Clear Channel Guide No / YES / Power on∙ DISPLAYNO/YES ∙ Line 1/LINEMost recently selected channel / input CH A/V Switchno / YESReminderno / YES Digit Entryno / YESHdmi Audio Selectionhdmi / AV1 / AV2 / AV Save Ccno / YESSource Menu Itemno / YES Save V-CHIPNO / YES Chip SetupSleeptimer Chip Menu Itemno / YESSecurity Standard / High Sleeptimer Countdown In Progress example26HW9100D Dimensions 30HW9100D Dimensions