Philips 26HW9100D, 30HW9100D user manual MAX Volume, Switch on Volumestandard / 0, Keyboard Lock

Page 18

L05 User’s Manual

091105.1833

MAX VOLUME

( 0 - 100)

Specify the highest volume setting possible by means of either the remote control, or the front panel (if it is not locked out). This setting cannot be less than MIN VOLUME (see

MIN VOLUME)

Note: The MAX VOLUME setting is effective whether the volume command is issued from the front panel (if it is not locked out), a standard guest- mode remote control, or an RC2573GR setup remote in setup mode.

SWITCH ON VOLUME(STANDARD / 0 - 100)

Specify the volume setting that takes effect when the TV is powered on.

If STANDARD, the volume at power-on will be the volume at which the TV was prior to last power-down.

If specified as 0 - 63, that will always be the volume at power-on, until SWITCH ON VOLUME is changed.

SWITCH ON CHANNEL

(STANDARD / TV 1-125 / AUX / FRONT

 

/ S-VIDEO / CVI)

Specify the channel / input to which the TV will be tuned when it is powered on.

If STANDARD, the channel at power-on will be that to which the TV was tuned at last power-down.

If specified (e.g., 2, AUX, etc.), then that will always be the channel / input at power-on, until SWITCH ON CHANNEL is changed.

POWER ON(STANDARD / FORCED /RESTORED)

STANDARD: The TV will be in standby mode when AC mains power is first applied after having been disconnected.

FORCED: The TV will turn ON whenever AC mains power is applied. This feature allows the TV’s power status to be controlled for example, from an AC mains breaker. RESTORED: When AC mains power is first applied after having been disconnected, the TV’s power status will revert to that when AC mains power was last removed.

CHANNEL DISPLAY(NONE / NUMBER / LABEL / ALL)

Specifies which of the respective channel properties are displayed by the TV’s OSD when a channel or input is first selected. If REMINDER (see REMINDER) is OFF, these properties will be displayed for a few seconds, then disappear. If REMINDER is ON, the channel properties remain on-screen whenever the TV is on.

KEYBOARD LOCK

(NO / YES)

NO:

The TV’s front panel is operational.

 

YES:

The TV’s front panel is rendered inoperative.

 

Note: Even when KEYBOARD LOCK = NO (not locked out), front panel power on/off, volume, or channel controls might have no effect, depending upon the settings of POWER ON (STANDARD / FORCED), CHANNEL INSTALL, MIN VOLUME, and

MAX VOLUME.

18

Image 18
Contents 26HW9100D/30HW9100D User’s Manual Safety Information Before Calling Service Symptom Possible Corrective ActionBasic Television Connection Use And Care of Remote Control Rear Jack Panel ConnectionsRemote Controls Guest Remote Control Keys DVD StopConsumer vs. Commercial Mode Accessing TV Setup MenusPage TV Setup Main Menu TV Setup Menu and Sub-Menus ∙ Video Blank Installing AV Inputs∙ Label ∙ Audio Mute∙ Major Channel Factory CH ResetCursor Right will reset the channels programmed in memory ∙ Minor ChannelEnter Digital Menu USE Channel Table NO/YESDigital OSDNO/YES Cursor Right will bring up the Consumer Digital Menu belowColor Default FormatBrightness ContrastUsing the different formats Noise Reductionno / YESAvloff / on Sound Mode Mono / StereoVolume BAR BalancePower Onstandard / Forced /RESTORED MAX VolumeSwitch on Volumestandard / 0 Channel Displaynone / Number / Label / ALLAUDIO/VIDEO OUT Mute ESPAUDIO/VIDEO Muteoff / Black / Blue Monitor OUT Rfno / YES∙ Line 1/LINE Channel Guide No / YES / Power on∙ DISPLAYNO/YES ∙ ClearDigit Entryno / YES CH A/V Switchno / YESReminderno / YES Most recently selected channel / inputSave Ccno / YES Source Menu Itemno / YESHdmi Audio Selectionhdmi / AV1 / AV2 / AV Chip Menu Itemno / YES Chip SetupSleeptimer Save V-CHIPNO / YESSleeptimer Countdown In Progress example Security Standard / High26HW9100D Dimensions 30HW9100D Dimensions