Philips FW-C380 manual Important notes for users in the U.K, Mains plug, How to connect a plug

Page 2

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp.

Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).

As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:

–Connect the blue wire to the terminal marked N or coloured black.

–Connect the brown wire to the terminal marked L or coloured red.

–Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio FW-C380 Philips risponde alle prescrizioni dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n. 548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips, Glaslaan 2

5616 JB Eindhoven,The Netherlands

Norge

Typeskilt finnes på apparatens underside.

Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk støt, skal apparatet ikke utsettes for regn eller fuktighet.

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

2

pg 01-30/C380/22-Eng

2

12/7/00, 3:42 PM

3139 115 20641

Page 1 Page 3
Image 2
Page 1 Page 3
Contents FW-C380 Mains plug How to connect a plugImportant notes for users in the U.K Copyright in the U.KTape 3139 115 155 107131 179Contents General Information Supplied AccessoriesSafety Information Environmental InformationPreparations Rear ConnectionsThey should be disposed off properly Inserting batteries into the Remote ControlPreparation CD / CD Controls on the player and remote controlSTANDBY-ON y Tape / Tape 1Controls Search à á Tuning à áPrev í / Next ëPRESET 4 Then select the desired function É, í, ë, etcPlug and Play Preparation proceduresOperating the System Switching the system to standby mode Demonstration modeSwitching the system on Selecting the Source DIM modeVolume Control Sound ControlTo switch on Optimal Sound Mix ¶ Press Optimal Sound MIX Press to select the VEC feature VEC led lights up¶ Press Incredible Surround to switch on Disc Direct Play Compact DiscDiscs for playback Selecting a desired track Playing a DiscDisc Change Searching for a particular passage during playbackReviewing the programme Erasing the programme when playback is stoppedShuffle only on remote control Playing the programmeSelect preset 10 before starting automatic Tuning to radio stationsStoring Preset Stations TunerManual programming Tuning to Preset Radio StationsReceiving RDS Radio Station Ç RDS Clock Setting the time with RDS clock Press ClocktimerTo cancel News function To start News functionLoading a tape This feature is available during tape playback onlyTape Auto ReplayDuring playback When playback is stoppedAux Load a blank tape in tape deck One Touch RecordingFor recording, use only tape of IEC type I normal tape Press Ç to stop recordingRecording from other sources RecordingCD Synchro Start Recording Digital Recording via Digital OutRecently selected volume level Clock/Timer¶ The volume of the timer will increase From the minimum level to the mostTo start the Timer again for the same To switch off the TimerPress and hold Clocktimer for more than 2 seconds While Sleep mode is activatedSpecifications Subject to modificationSymptom Remedy MaintenanceTroubleshooting Level System does not react when anyRecording or playback cannot be Tape deck door cannot open
Top Page Image Contents