Philips SVA104 owner manual Auto Return

Page 30

30 Auto Return

Follow the steps below to make the VCR rewind to the beginning of the programs after it has finished all timer recordings. Make sure:

●The VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.)

1

Press the MENU button repeatedly until the VCR SET UP menu appears.

VCR SET UP

→ SATELLITE LINK AUTO REPEAT RENTAL AUTO RETURN

2

Press the PLAY button or the STOP button repeatedly to select AUTO RETURN.

VCR SET UP

SATELLITE LINK

AUTO REPEAT RENTAL

→ AUTO RETURN

3

Press the F.FWD button so that [AUTO] appears next to AUTO RETURN on-screen.

VCR SET UP

SATELLITE LINK

AUTO REPEAT RENTAL

→ AUTO RETURN [AUTO]

1

2

POWER

VCR/TV

EJECT

1 2 3

4 5 6

7 8 9 CHANNEL

	SPEED	0	+100
	SLOW	QUICK-	SEARCH
		QUICK-	TIME	INDEX
		FIND	TIME	INDEX
		FIND
	MENU	DISPLAY	EXIT	COUNTER
			RESET	MEMORY
	REWIND	/ PLAY		F.FWD
	RECORD		/ STOP	PAUSE/STILL

4

3

4

Press the COUNTER RESET/EXIT button to exit. Remember to turn off the VCR before the timer recording. When all the timer recordings are completed, the TIMER light will flash and the VCR will rewind the tape to the beginning of the record- ed programs.

Helpful Hints

•If additional timer recordings are programmed to take place later, the Auto Return function will not operate until all the programs are recorded.

•To cancel this function, follow steps 1 - 2 above. At step 3, press the F.FWD button so that [AUTO] no longer appears beside AUTO RETURN. Press the COUNTER RESET/EXIT button to exit.

Image 30

Contents Video Cassette Recorder Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR maintenanceHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRConnections Recording/Viewing Any ChannelCable Box/DBS SignalRecording One Channel/Watching Another CableHookups With a Stereo TV Turning on Your VCR 2Turn on the TVAutomatic Channel Setup Automatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d 96-7Press the Counter RESET/EXIT button to exit Language SelectionOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Status Displays Remote Control Buttons Time Search Button Counter RESET/EXIT ButtonEject Button Index Search ButtonVCR Display Panel Front Panel Video OUT Jack AC Power CordRear Panel Video in JackPlaying Read and follow the steps below to play a tapeRecording 1Turn on the TV Insert a tapeOne-Touch Recording Starting an OTRStopping an OTR Timer Recording Program Number → Once Daily WeeklyTimer Recording cont’d Repeat the procedure in to set the recording’s end time4Press the Counter RESET/EXIT button to exit Cancelling a Timer Recording Correcting a Timer RecordingAuto Return Auto Satellite Link Using a Satellite Tuner To return to the channel being recorded, use the TV Press the VCR/TV button on the VCR remote control toRecording One Channel/Watching Another Put the VCR in VCR position. The VCR/TV light will appearRerecording Tape Duplication AntennaRepeat Play Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureRental Play Menu will disappear, and Rental on or RentalTo on or OFF Real-Time Counter Memory Press the Play button to watch the tapeIndex Search Time Search Time Search is not available during recordingQuick Find To resume normal tape playback, press the Play buttonAutomatic Playback Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel Channel 3 orSpecifications Limited Warranty Video Cassette RecorderIndex Supplied Accessories