Philips SVA104 owner manual Repeat Play

Page 34

34 Repeat Play

Follow the steps below to program the VCR to play a tape over and over. Make sure:

●The VCR is on and is in VCR position. The VCR/TV light will appear on the front panel. If it does not, press the VCR/TV but- ton once.

●There is a tape in the VCR.

1

Press the MENU button repeatedly until the VCR SET UP menu appears.

VCR SET UP

→SATELLITE LINK AUTO REPEAT RENTAL AUTO RETURN

2

Press the PLAY button or the STOP button repeatedly to select AUTO REPEAT.

VCR SET UP

SATELLITE LINK

→AUTO REPEAT RENTAL AUTO RETURN

3

Press the F.FWD button so that [ON] appears next to AUTO REPEAT. Tape playback will begin immediately. AUTO REPEAT B will appear on-screen briefly.

(If you are fast forwarding or rewinding the tape, you must first press the COUNTER RESET/EXIT button to exit, then press the PLAY button to begin tape playback.)

The VCR will play the tape to the end, rewind it, then play it again. (TV programming will appear on-screen while the tape is rewinding.)

POWER

VCR/TV

EJECT

1 2 3

4 5 6

7 8 9 CHANNEL

	SPEED	0	+100
	SLOW	QUICK-	SEARCH
1	SLOW	FIND	TIME	INDEX
		FIND
	MENU	DISPLAY	EXIT	COUNTER
			RESET	MEMORY	3
	REWIND	/ PLAY		F.FWD
	RECORD		/ STOP	PAUSE/STILL
	RECORD			PAUSE/STILL

2

Helpful Hints

•To cancel AUTO REPEAT, follow steps 1 - 2 above. At step 3, press the F.FWD button so that [ON] no longer appears beside AUTO REPEAT. Press the COUNTER RESET/EXIT button to exit.

•The COUNTER MEMORY button does not function if AUTO REPEAT is set to [ON].

•The real-time counter memory is cancelled if AUTO REPEAT is set to [ON].

Image 34

Contents Video Cassette Recorder Warranty Verification For Customer UseSafety Precautions FeaturesIntroduction Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR maintenanceHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRConnections Recording/Viewing Any ChannelCable Box/DBS SignalRecording One Channel/Watching Another CableHookups With a Stereo TV Turning on Your VCR 2Turn on the TVAutomatic Channel Setup Automatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d 96-7Press the Counter RESET/EXIT button to exit Language SelectionPress the Display button once Clock mode OFF mode Press the Display button once Count modeOn-Screen Status Displays Remote Control Buttons Time Search Button Counter RESET/EXIT ButtonEject Button Index Search ButtonVCR Display Panel Front Panel Video OUT Jack AC Power CordRear Panel Video in JackPlaying Read and follow the steps below to play a tapeRecording 1Turn on the TV Insert a tapeStarting an OTR One-Touch RecordingStopping an OTR Timer Recording Program Number → Once Daily WeeklyTimer Recording cont’d Repeat the procedure in to set the recording’s end time4Press the Counter RESET/EXIT button to exit Cancelling a Timer Recording Correcting a Timer RecordingAuto Return Auto Satellite Link Using a Satellite Tuner To return to the channel being recorded, use the TV Press the VCR/TV button on the VCR remote control toRecording One Channel/Watching Another Put the VCR in VCR position. The VCR/TV light will appearRerecording Tape Duplication AntennaRepeat Play Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureMenu will disappear, and Rental on or Rental Rental PlayTo on or OFF Real-Time Counter Memory Press the Play button to watch the tapeIndex Search Time Search Time Search is not available during recordingQuick Find To resume normal tape playback, press the Play buttonAutomatic Playback Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel Channel 3 orSpecifications Limited Warranty Video Cassette RecorderIndex Supplied Accessories