Philips SVA104 owner manual CH3 CH4, Plug in the TV and the VCR

Page 7

Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

ANT

IN

					AUDIO
				ANT	OUT IN	OUT
				ANT	VIDEO	CH3 CH4
					VIDEO
				IN		75V
						75V
						ANT	/
AUDIO						CABLE
AUDIO
OUT	IN			OUT			ANTENNA IN Jack
							ANTENNA IN Jack
VIDEO		CH3	CH4				(on back of TV)
VIDEO						RF coaxial cable	example only
							example only

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

ANT

IN

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

AUDIO
OUT	IN	OUT
VIDEO		CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Contents Video Cassette Recorder For Customer Use Warranty VerificationSafety Precautions FeaturesIntroduction Table of Contents VCR maintenance Before Using Your VCRPutting Batteries in the Remote Control Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemPlug in the TV and the VCR CH3 CH4Recording/Viewing Any Channel ConnectionsCable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV 2Turn on the TV Turning on Your VCRAutomatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’dFollow the steps below to set your VCR’s clock. Make sure Setting the Clock96-7 Setting the Clock cont’dLanguage Selection Press the Counter RESET/EXIT button to exitPress the Display button once Clock mode OFF mode Press the Display button once Count modeOn-Screen Status Displays Remote Control Buttons Index Search Button Counter RESET/EXIT ButtonEject Button Time Search ButtonVCR Display Panel Front Panel Video in Jack AC Power CordRear Panel Video OUT JackRead and follow the steps below to play a tape Playing1Turn on the TV Insert a tape RecordingStarting an OTR One-Touch RecordingStopping an OTR Program Number → Once Daily Weekly Timer RecordingRepeat the procedure in to set the recording’s end time Timer Recording cont’d4Press the Counter RESET/EXIT button to exit Correcting a Timer Recording Cancelling a Timer RecordingAuto Return Auto Satellite Link Using a Satellite Tuner Put the VCR in VCR position. The VCR/TV light will appear Press the VCR/TV button on the VCR remote control toRecording One Channel/Watching Another To return to the channel being recorded, use the TVAntenna Rerecording Tape DuplicationRepeat Play Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPMenu will disappear, and Rental on or Rental Rental PlayTo on or OFF Press the Play button to watch the tape Real-Time Counter MemoryIndex Search Time Search is not available during recording Time SearchTo resume normal tape playback, press the Play button Quick FindAutomatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or GlossarySpecifications Video Cassette Recorder Limited WarrantyIndex Supplied Accessories