Philips VRX342AT On-Screen Status Displays, Press the Number 2 button to select on Screen Mode

Page 24

24 On-Screen Status Displays

A status display, which includes the current time, channel, and other information (see illustration), will appear when you press the STA- TUS/EXIT button or certain function buttons. The contents of the sta- tus display may vary. There are three status display modes:

ON SCREEN ON:

●Whenever you press the STOP button or the PLAY button, the sta- tus display will appear for five seconds.

COUNTER ONLY:

●Whenever you press the STOP button or the PLAY button, the sta- tus display will appear for five seconds. After five seconds, only the counter will remain on-screen. You must press the STATUS/EXIT button to remove it.

ON SCREEN OFF:

●The status display will not appear when you press function buttons. You must press the STATUS/EXIT button to see the status display.

To choose the status display mode, follow the steps below.

1

Press the VCR button, then press the MENU button to bring up the main menu display.

Function

Button

Pressed Time

STOP			12:00 AM
			CH10
SLP		M 1:23:45

			Channel
Tape		Counter
Speed		and
		Counter
		Memory

TO SELECT PUSH NO. SHOWN

1PROGRAM

2VCR SET UP

3TUNER SET UP

4SET CLOCK

TO END PUSH EXIT

2

Press the Number 2 button to select VCR SET UP.

TO SELECT PUSH NO. SHOWN

1 REPEAT PLAY

OFF

2ON SCREEN MODE

3LANGUAGE

4VCR PLUS+ REF. MAP

TO END PUSH EXIT

3

Press the Number 2 button to select ON SCREEN MODE.

TO SELECT PUSH NO. SHOWN

1 ON SCREEN ON

ON

2COUNTER ONLY

3ON SCREEN OFF

TO END PUSH EXIT

4

Press the Number 1 button to select ON SCREEN ON, the Number 2 button to select COUNTER ONLY, or the Number 3 button to select ON SCREEN OFF. ON will appear beside the selected status display mode.

5

Press the STATUS/EXIT button to exit.

Helpful Hints

•If the channel you select has no broadcast, the screen will become a solid blue field. The screen will remain blue until you select an active channel.

•You may bring up the status display at any time by pressing the STA- TUS/EXIT button.

(The exception is when viewing a still picture or a slow motion picture, or when F.FWD or REW(ind) is pressed during playback.)

•Channel numbers (when tuned) are displayed for a few seconds.

Image 24

Contents VRX342AT Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction UseTable of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Remove the battery compartment lid on the bottomHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRTimer Recordings Hookups With a Cable BoxRecording/Viewing Any Channel Watching TV With the VCR OffHookups With a Cable Box cont’d Recording One Channel/Watching AnotherPlaying a Tape Press the Play button to play the tapeHookups With a Stereo TV Turning on Your VCR 1Turn on the TVPress the Number 3 button to select Tuner SET UP Channel MemoryProgramming Channels Press the VCR buttonAdding/Deleting Channels Reviewing Programmed ChannelsUse the Number buttons to enter the channel number Setting the Clock Manual Clock SettingPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual ClockSetting the Clock cont’d Setting the Clock cont’d Automatic Clock SettingPress the VCR button, then press the Menu button to Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 2 button to select VCR SET UP Language SelectionLanguage Selection Press the Number 3 button to select LanguageTV Code Setting Press and release the Mute buttonWithin 30 seconds after releasing the Mute button, press Release the TV buttonFind the brand of your Cable Box or Satellite System on Release the CABLE/DSS buttonWithin 30 seconds after releasing the CABLE/DSS button, use Remote Control Buttons Remote Control Buttons cont’d Press the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below VCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tapePress the VCR button on the remote control RecordingRecording One Channel/Watching Another Press the Stop button to stop the recordingChannels are programmed With the Tape Speed buttonIntact and the tape is long enough to record the programs Buttons to select the channel you want to recordTimer Recording DailyRecording Menu ScreenTimer Recording cont’d Enter the recording’s stop timeTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings See page 46 for more hintsSetting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Press the VCR button, then press the Menu button Press the Number 4 button to select VCR PLUS+ REF. MAPPanel of the VCR. If it does not, press the VCR/TV button OnceTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemorySpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories