Philips VRX342AT warranty Rerecording Tape Duplication

Page 40

40 Rerecording (Tape Duplication)

1. Audio cable from AUDIO OUT Jack of VCR 1 to AUDIO IN Jack of VCR 2

VCR 1 - Playing VCR

VCR 2 - Recording VCR

 

 

 

ANT

 

 

 

ANT

 

 

 

IN

 

 

 

IN

AUDIO

 

 

AUDIO

 

 

OUT

IN

 

OUT

OUT

IN

 

OUT

VIDEO

CH3

CH4

VIDEO

CH3

CH4

 

 

 

 

2. Video cable from VIDEO OUT Jack of VCR 1 to VIDEO IN Jack of VCR 2

The instructions on this page show you how to copy tapes. The illustration uses two VCRs just like yours. Different VCRs may operate differently.

NOTE: Unauthorized recording of copyrighted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws.

3.RF coaxial cable (supplied) from

VCR’s OUT Jack to TV’s ANTENNA IN Jack

1

Make the connections shown above.

2

VCR 1 will play your tape. Insert a prerecorded tape in VCR

1.If the tape does not have a record tab, playback begins. If this happens, press the STOP/EJECT button on VCR 1 once.

3

VCR 2 will record your tape. Insert a blank tape in VCR 2. Make sure the VCR 2 power is on and VCR 2 is in VCR position. (The VCR light will appear on the display panel. If it does not, press the TV/VCR button once.)

4

Turn the TV on and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on VCR 2 is set to.

5

Point the remote control at VCR 2. Press Number but- tons 0, 0, 1 or 0, 0, 2.

6

Point the remote control at VCR 2. Use the (Tape) SPEED button to select SP, LP or SLP.

7

Press the PLAY button on VCR 1 and the REC(ord)/OTR button on VCR 2 at the same time.

To stop recording, press the STOP/EJECT button on VCR 1, then press the STOP/EJECT button on VCR 2.

Helpful Hints

If you use the AUDIO and VIDEO IN Jacks on the back of VCR 2, press Number buttons 0, 0, 1. AV REAR will appear on-screen.

If you use the AUDIO and VIDEO IN Jacks on the front of VCR 2, press Number buttons 0, 0, 2. AV FRONT will appear on-screen.

Image 40
Contents VRX342AT Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction UseTable of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Remove the battery compartment lid on the bottomHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRTimer Recordings Hookups With a Cable BoxRecording/Viewing Any Channel Watching TV With the VCR OffHookups With a Cable Box cont’d Recording One Channel/Watching AnotherPlaying a Tape Press the Play button to play the tapeHookups With a Stereo TV Turning on Your VCR 1Turn on the TVPress the Number 3 button to select Tuner SET UP Channel MemoryProgramming Channels Press the VCR buttonReviewing Programmed Channels Adding/Deleting ChannelsUse the Number buttons to enter the channel number Setting the Clock Manual Clock SettingPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual ClockSetting the Clock cont’d Setting the Clock cont’d Automatic Clock SettingPress the VCR button, then press the Menu button to Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 2 button to select VCR SET UP Language SelectionLanguage Selection Press the Number 3 button to select LanguageTV Code Setting Press and release the Mute buttonWithin 30 seconds after releasing the Mute button, press Release the TV buttonRelease the CABLE/DSS button Find the brand of your Cable Box or Satellite System onWithin 30 seconds after releasing the CABLE/DSS button, use Remote Control Buttons Remote Control Buttons cont’d On-Screen Status Displays Press the Number 2 button to select on Screen ModeTo choose the status display mode, follow the steps below VCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tapePress the VCR button on the remote control RecordingRecording One Channel/Watching Another Press the Stop button to stop the recordingChannels are programmed With the Tape Speed buttonIntact and the tape is long enough to record the programs Buttons to select the channel you want to recordTimer Recording DailyRecording Menu ScreenTimer Recording cont’d Enter the recording’s stop timePress the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Checking or Cancelling Timer Recordings See page 46 for more hintsTV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Press the VCR button, then press the Menu button Press the Number 4 button to select VCR PLUS+ REF. MAPPanel of the VCR. If it does not, press the VCR/TV button OnceTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemorySpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories