Philips VRX342AT Hookups Without a Cable Box, Disconnect the antenna or cable from your TV

Page 6

6 Hookups Without a Cable Box

The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a descrambler box, please refer to pages eight-nine. If you have a Stereo TV, please go to page 10. After you hook up the VCR, please go to page 11 to turn on the VCR.

1

Disconnect the antenna or cable from your TV.

Antenna

Indoor/Outdoor

(300 ohm)

75V
ANT	/
CABLE

75V

ANT /

CABLE

OR

ANTENNA IN

Jack

(on back of TV)

Cable

(75 ohm)

2

Connect the antenna or cable to the ANT(enna) IN Jack of your VCR.

Antenna

Indoor/Outdoor

(300 ohm)

OR

Cable

(75 ohm)

Back of VCR

ANT

IN

	AUDIO
ANT	OUT IN		OUT
ANT	VIDEO	CH3	CH4
	VIDEO

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

Image 6

Contents VRX342AT Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions UseTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Remove the battery compartment lid on the bottomHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRRecording/Viewing Any Channel Timer RecordingsHookups With a Cable Box Watching TV With the VCR OffPlaying a Tape Hookups With a Cable Box cont’dRecording One Channel/Watching Another Press the Play button to play the tapeHookups With a Stereo TV Turning on Your VCR 1Turn on the TVProgramming Channels Press the Number 3 button to select Tuner SET UPChannel Memory Press the VCR buttonAdding/Deleting Channels Reviewing Programmed ChannelsUse the Number buttons to enter the channel number Press the Number 4 button to select SET Clock Setting the ClockManual Clock Setting Press the Number 2 button to select SET Manual ClockSetting the Clock cont’d Press the VCR button, then press the Menu button to Setting the Clock cont’dAutomatic Clock Setting Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageWithin 30 seconds after releasing the Mute button, press TV Code SettingPress and release the Mute button Release the TV buttonFind the brand of your Cable Box or Satellite System on Release the CABLE/DSS buttonWithin 30 seconds after releasing the CABLE/DSS button, use Remote Control Buttons Remote Control Buttons cont’d Press the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below VCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tapePress the VCR button on the remote control RecordingRecording One Channel/Watching Another Press the Stop button to stop the recordingIntact and the tape is long enough to record the programs Channels are programmedWith the Tape Speed button Buttons to select the channel you want to recordRecording Menu Timer RecordingDaily ScreenTimer Recording cont’d Enter the recording’s stop timeTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings See page 46 for more hintsSetting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Press the VCR button, then press the Menu button Press the Number 4 button to select VCR PLUS+ REF. MAPPanel of the VCR. If it does not, press the VCR/TV button OnceTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemorySuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories