Philips VRA611AT owner manual Hookups With a Stereo TV, Video Cable

Page 10

10 Hookups With a Stereo TV

			antenna or
			1 ANT(enna)cable to
AUDIO		ANT	IN Jack
	L	IN
OUT	IN
	R
VIDEO		OUT
OUT	IN	CH3 CH4
OUT	IN
VIDEO (yellow) and		2
AUDIO (red and white)			Video Cable
OUT Jacks			Video Cable
OUT Jacks

Audio and Video IN Jacks on TV

● Audio and Video cables are not supplied. 3 Audio Cable

1

Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.

2

Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV.

3

Connect an audio cable to the red and white AUDIO OUT Jacks on the back of the VCR. Then, connect the other end of the audio cable to the AUDIO IN Jacks on your TV.

4

Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owner’s manual for details.

Helpful Hint

• A stereo audio cable (not supplied) is used here to deliver audio to the TV’s left and right channels.

• The TV must be in Line Input mode. Please refer to your TV owner’s manual.

Image 10

Contents VRA611AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents Before Using Your VCR Hookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another TV’s AntennaHookups With a Stereo TV Video Cable2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock SET CLOCK, then press the F.FWD/ B buttonDaylight-Savings Time Press the VCR buttonLanguage Selection Remote Control Buttons Press again to resume normal playback REWind/ ButtonSTOP/p Button MenuIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR If the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once Recording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Press the VCR button, then press the Menu button Timer RecordingDo each step within 60 seconds of the previous step DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsTimer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication RF coaxial cableRepeat Play Press the F.FWD/B button so that on appears besideReal-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Time Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Specifically… Multi-Channel Television Sound SystemUnderstanding On-Screen Displays MonitorMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onHi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Timer PowerRemote control AutomaticSupplied Accessories