Philips VRA611AT owner manual Hookups Without a Cable Box/Direct Broadcast System

Page 6

6 Hookups Without a Cable Box/Direct Broadcast System

The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR.

1

Disconnect the antenna or cable from your TV.

Antenna

Indoor/Outdoor

(300 ohm)

75V
ANT	/
CABLE

75V

ANT /

CABLE

OR

ANTENNA IN

Jack

(on back of TV)

Cable

(75 ohm)

2

Connect the antenna or cable to the ANT(enna) IN Jack of your VCR.

Antenna

Indoor/Outdoor

(300 ohm)

OR

Cable

(75 ohm)

Back of VCR

			AUDIO		ANT
			AUDIO		IN
			L		IN
			L
			OUT	IN
			R
		ANT	VIDEO		OUT
			OUT	IN	CH3 CH4
			OUT	IN
AUDIO
AUDIO		IN
	L	IN
	L
OUT	IN
	R
VIDEO		OUT
VIDEO
OUT	IN CH3	CH4

Image 6

Contents VRA611AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Hookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRHookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Recording One Channel/Watching Another TV’s AntennaHookups With a Stereo TV Video Cable2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock SET CLOCK, then press the F.FWD/ B buttonDaylight-Savings Time Press the VCR buttonLanguage Selection Remote Control Buttons Press again to resume normal playback REWind/ ButtonSTOP/p Button MenuIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape in the VCR Recording If the VCR light appears on the display panel, go to . IfVCR light does not appear, press the VCR/TV button once Recording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Press the VCR button, then press the Menu button Timer RecordingDo each step within 60 seconds of the previous step DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication RF coaxial cableRepeat Play Press the F.FWD/B button so that on appears besideClear button to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on the screen, press Time Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Specifically… Multi-Channel Television Sound SystemUnderstanding On-Screen Displays MonitorMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onHi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Timer PowerRemote control AutomaticSupplied Accessories