Philips VRA611AT owner manual Timer Recording cont’d

Page 29

Timer Recording (cont’d) 29

4

Use the Number buttons (1-8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen.

NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly. Information about the program in that slot will appear on the screen. If this happens, press the STATUS/EXIT button, then select another number.

5

Use the Number buttons to enter the channel you want to record.

●Cable Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. There also may be a brief delay when you select channels 10, 11, and 12. If you want to select channels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7.

Antenna Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay. You may only select channels 2-69.

●If you are recording from line input, press 0,0 to select A/V IN.

●If you are using a Cable Box/DBS, select the Cable Box/DBS out- put channel (03 or 04). Set the Cable Box/DBS to the channel you want to record. Leave the Cable Box/DBS on for the timer recording. See page eight for details.

4-7

POWER VCR/TV EJECT

VCR

TV

	PLAY
REW		F.FWD
	STOP
MENU	STATUS/EXIT	CLEAR

1	2	3
4	5	6	CH
4	5	6
7	8	9
		ALT. CH
	0		VOL
	0
SPEED	TIME SEARCH PAUSE/STILL

REC/OTR MEMORY SLOW MUTE

6

Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	10
TIME ON	– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

7

Follow the instructions in step 6 to enter the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

Instructions continue on page 30.

Helpful Hint

•Entries that do not match the VCR’s clock or calendar will cause a ques- tion mark to appear on the screen.

Image 29

Contents VRA611AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoIntroduction FeaturesSafety Precautions Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Recording One Channel/Watching AnotherVideo Cable Hookups With a Stereo TVTurning on Your VCR Press the VCR button, then press the Power button2Turn on the TV Press the Menu button. The display shown below will appearPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSET CLOCK, then press the F.FWD/ B button Setting the ClockPress the VCR button Daylight-Savings TimeLanguage Selection Remote Control Buttons STOP/p Button REWind/ ButtonPress again to resume normal playback MenuStatus Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape VCR light does not appear, press the VCR/TV button once RecordingIf the VCR light appears on the display panel, go to . If VCR light will disappear from the VCR’s display panel Recording One Channel/Watching AnotherOne-Touch Recording Do each step within 60 seconds of the previous step Timer RecordingPress the VCR button, then press the Menu button DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dProgram REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsTimer recording information for the program in the lowest RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayWhile the status display is on the screen, press Clear button to reset the real-time counter to zeroReal-Time Counter Memory Press the VCR button Press the Time Search button Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemSpecifically… MonitorMulti-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemHi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyRemote control PowerTimer AutomaticSupplied Accessories