Philips VRA611AT owner manual Helpful Hints cont’d

Page 43

Helpful Hints (cont’d) 43

TV programs cannot be watched normally.

•Put the VCR in TV position. (Press the VCR/TV button so that the VCR light disappears from the display panel. For details, see page 22.)

•Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if applicable). (See pages six-10 for details.)

Tape cannot be inserted.

•Insert the tape, window side up, with the record tab facing you.

•Make sure a tape isn’t already in the VCR by pressing the STOP/EJECT button on the VCR.

•Gently push on the center of the tape when putting it in the VCR. Never force the tape into the VCR.

•If a timer recording is programmed and the VCR power is off, you can not insert a tape without a record tab.

Tape cannot be removed.

•Make sure the power plug is completely connected to a power outlet.

•You have set a timer recording. Turn the VCR power on, then eject the tape. Be sure to insert a tape and turn off the power for your timer recording.

VCR ejects the tape when the REC(ord)/OTR button is pressed or when the VCR power is turned off to set a timer recording.

•Make sure the tape has a record tab (page five).

Poor reception

•You may need to tune your TV again.

The motor (cylinder) rotates even when the VCR is in Stop mode.

•To enable the quick play mechanism, the cylinder will rotate for about five minutes. This is normal. The quick play mechanism allows the tape mechanism to switch from Stop mode to Play mode in one second.

Direct Broadcast System Hookups

•Watching one TV channel while recording another may not be possible if you have a DBS hookup. You may have to set your TV to channel 03 or 04, then make your channel selections at the DBS.

•With many DBS hookups, if you use accessory audio and video cables to connect your VCR to your TV, you will have to put your VCR in Line Input mode (channel 00).

Line Input mode

•If you accidentally enter Line Input mode (A/V IN will appear on your TV screen briefly), press the CH(annel) o/p button or use the Number buttons to select another channel.

Hi-Fi Stereo Sound

•During playback, Hi-Fi audio may temporarily revert to normal audio when you adjust tracking. This is normal.

•When connecting the VCR to a stereo TV, you will only get stereo sound if you use audio cables to con- nect the AUDIO OUT jacks on the VCR to the AUDIO IN jacks on your TV, and if the TV is in Line (Auxiliary) Input mode.

•When you connect the AUDIO OUT jacks on the VCR to the AUDIO IN jacks on your TV, the stereo light on the TV might not glow. But, as long as the status display indicates you are receiving a stereo sig- nal, you are receiving a stereo signal. This is normal.

•Only tapes recorded in Hi-Fi audio will play back in Hi-Fi audio. Tapes recorded in normal audio will play back in monaural audio.

Page 42 Page 44
Image 43
Page 42 Page 44
Contents VRA611AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialSafety Precautions FeaturesIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dConnections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel TV’s Antenna Recording One Channel/Watching AnotherVideo Cable Hookups With a Stereo TVPress the Menu button. The display shown below will appear Press the VCR button, then press the Power buttonTurning on Your VCR 2Turn on the TVPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSET CLOCK, then press the F.FWD/ B button Setting the ClockPress the VCR button Daylight-Savings TimeLanguage Selection Remote Control Buttons Menu REWind/ ButtonSTOP/p Button Press again to resume normal playbackIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR If the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once VCR light will disappear from the VCR’s display panel Recording One Channel/Watching AnotherOne-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Press the VCR button, then press the Menu buttonTimer Recording cont’d Tape Speeds Timer Recording cont’dTimer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayReal-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Press the VCR button Press the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monitor Multi-Channel Television Sound SystemUnderstanding On-Screen Displays Specifically…Multi-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemHi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyAutomatic PowerRemote control TimerSupplied Accessories
Top Page Image Contents