Q-Logic 9100, 59229-05 A manual Replacing I/O Blades

Page 124

5–Customer Replaceable Units Replacing I/O Blades

Replacing I/O Blades

You can remove and install I/O blades while the switch is operating. The following instructions assume that the switch is operating. If you want to maintain service to the devices connected to a particular blade while it is being replaced, transfer the Fibre Channel cables to another I/O blade. Mechanically, these instructions also apply to removing and installing a I/O blade blank panel.

The following removal and installation procedures describe how to remove an I/O blade using the CLI. Refer to the SANbox 9000 Series Stackable Chassis Switch Command Line Interface Guide for information about the CLI commands.

CAUTION!

Always use an ESD wrist strap when removing and installing an I/O blade. An I/O blade contains sensitive logic components. Keep the I/O blade in an ESD protective container or anti-static bag when not in use.

ATTENTION!

Portez toujours un bracelet antistatique lors du retrait et de l'installation d'une lame d'E/S. Les lames d'E/S contiennent des composants logiques sensibles. Lorsque vous ne l'utilisez pas, conservez la lame d'E/S dans un conteneur ou un sachet antistatique.

VORSICHT!

Benutzen Sie immer ein ESD-Handgelenkband, wenn Sie eine E/A-Steckkarte entfernen oder installieren. Eine E/A-Steckkarte enthält empfindliche Steuerkomponenten. Bewahren Sie die E/A- Steckkarte in einem ESD-Schutzcontainer oder Antistatikbeutel auf, wenn sie nicht benutzt wird.

¡PRECAUCIÓN!

Utilice siempre una muñequera antiestática cuando elimine e instale una placa de E/S. Una placa de E/S contiene componentes lógicos sensibles. Guarde la placa de E/S en un contenedor protector ESD o en una bolsa antiestática cuando no se utilice.

5-12

59229-05 A

Image 124
Contents QLogic 9000 Series Stackable Chassis Switch Document Revision History Table of Contents Planning Installation Diagnostics/TroubleshootingSpecifications Customer Replaceable UnitsGlossary Index List of Figures List of Tables Preface Intended AudienceRelated Materials Sicherheitshinweise Safety NoticesAdvertencias de seguridad Communications Statements Federal Communications Commission FCC Class a StatementCE Statement Electrostatic Discharge Sensitivity Esds Precautions Laser Safety InformationVcci Class a Statement Pièces Accessibles Accessible PartsZugängliche Teile License Agreements New in this ReleaseTechnical Support AvailabilityTraining Contact InformationPreface Technical Support Xviii 59229-05 a QLogic 9000 Series Switch Models Hardware OverviewQLogic 9000 Series Switch Model Components Maintenance Panel Maintenance PanelBlades I/O Blades Blade LEDs FC Port LEDsPort Types Transceivers and 10-Gbps Stacking Cables CPU Blades CPU BladeCPU Blade LEDs Resetting a CPU Blade Maintenance ButtonPlacing the Switch in Maintenance Mode Ethernet Port Serial Port Power Supply BladesInter-Chassis Connection Ports Power Supply Blade Fan Blades Fan BladeFabric and Switch Management Enterprise Fabric SuiteQuickTools Command Line Interface Storage Management Initiative-Specification SMI-SApplication Programming Interface Simple Network Management ProtocolPlanning DevicesDevice Access Zoning Database LimitsPerformance DistanceBandwidth Extended Credit Distances and Cable LengthsLatency Feature LicensingPort-to-Port Latency Multiple Chassis Fabrics Single Switch Fabric with Initiators and Targets Optimizing Device PerformanceDomain ID, Principal Priority, and Domain ID Lock Interconnecting QLogic 9000 Series Switches Switch Services Planning Switch Services Security Internet Protocol SupportUser Account Security Port Binding IP SecurityConnection Security Device Security Security Example Switches and HBAs with Authentication Security Example Switches and HBAsHBA1 Node WWN 100000c0dd07e34e Security Example Radius Server Security Example Radius ServerPlanning Security HBA1 Save and activate SecuritySet2 on Switch2 Security Example Host Authentication Security Example Management ServerPlanning Security Fabric Management Installation Site RequirementsSwitch Power Requirements Fabric Management WorkstationEnvironmental Conditions Management Workstation RequirementsInstalling a Switch QLogic 9000 Series Stackable Chassis SwitchInstallation Installing a Switch Mount the Switch AvertissementVorsicht ¡PRECAUCIÓN QLogic 9000 Series Rail Kit Warnung Install I/O Blades Installing an I/O BladeStack the Switches Installing Stacking CablesInstall Transceivers Power Up the Switch Warnung Attaching the Power Cord Restraint Bail Configure the Workstation Setting the Workstation IP Address for Ethernet ConnectionsConfiguring the Workstation Serial Port Install Enterprise Fabric Suite Connect the Workstation to the SwitchObtain the Network Configuration Start Enterprise Fabric Suite Configure the Switch Network Configuration ParametersCable Devices to the Switch Installing Firmware Using Enterprise Fabric Suite 2007 to Install Firmware Using QuickTools to Install FirmwareUsing the CLI to Install Firmware One-Step Firmware InstallationEnter the password for your account name FTP only Custom Firmware Installation Adding a Switch to an Existing Fabric Installing Feature License Keys HyperStacking HyperStack Cable Connector Securing HyperStack Cables WWN Installation HyperStacking 59229-05 a Installation HyperStacking 59229-05 a Diagnostics/Troubleshooting Power-On Self Test Error Code Blink PatternsFatal Post Error Blink Pattern System Error Blink PatternInternal Firmware Failure Blink Pattern Internal Firmware Failure Blink PatternConfiguration File System Error Blink Pattern QLogic $admin start CPU Blade Diagnostics CPU Blade Diagnostic ProcessBlade Diagnostics I/O Blade Diagnostic ProcessFC Port Diagnostics Logged-In LEDEPort Isolation Excessive Port Errors Diagnostics/Troubleshooting FC Port Diagnostics Transceiver Diagnostics Power Supply Blade Diagnostics Power Supply Blade Diagnostics ProcessFan Blade Diagnostics Fan Blade Diagnostic ProcessRecovering a Switch Using Maintenance Mode Exiting the Maintenance Menu Unpacking a Firmware Image FileResetting the Network Configuration Resetting User AccountsRemoving the Switch Configuration Copying Log FilesResetting a Blade Remaking the File SystemCustomer Replaceable Units QLogic 9000 Series Customer Replaceable Units Replacing Transceivers and Stacking Cables Replacing CPU Blades CPU blade heat sinks can become very hot. Handle with care Standard Single CPU Primary CPU Blade Replacement Removing the CPU0 Blade Customer Replaceable Units Replacing CPU Blades Standard Dual CPU Primary CPU Blade Replacement Fault Tolerant Primary CPU Blade Replacement Secondary CPU Blade Replacment Replacing I/O Blades Removing an I/O Blade Removing an I/O Blade Installing an I/O Blade Replacing Power Supply Blades Vorsicht ¡PRECAUCIÓN Removing a Power Supply Blade Removing a Power Supply BladeInstalling a Power Supply Blade Replacing Fan Blades Vorsicht Installing a Fan Blade Removing a Fan BladeCustomer Replaceable Units Replacing Fan Blades 59229-05 a Specifications Fabric Specifications Table A-1. Fabric SpecificationsOptional License Keys Table A-2. Optional License KeysPerformance Features Table A-3. Performance FeaturesSpecifications Performance Features Modular Scalability Table A-4. Modular ScalabilityTable A-4. Modular Scalability Fabric Services Table A-6. Fabric ServicesInteroperability/Certifications Table A-5. Interoperability/CertificationsSpecifications Fabric Services Maintainability Table A-7. MaintainabilityPhysical Characteristics Table A-8. Physical Characteristics 150 CFM air flow Electrical Requirements Table A-9. Electrical RequirementsPower Cord Specifications Table A-10. Availalbe Power CordsEnvironmental Factors Table A-11. Environmental FactorsRegulatory Certifications Table A-12. Regulatory CertificationsSpecifications Regulatory Certifications 59229-05 a Glossary CRU Fdmi SMI-S Vcci Page Index Index-2 59229-05 a 59229-05 a Index-3 LED 59229-05 a Index-5 Index-6 59229-05 a 59229-05 a Index-7 Page
Related manuals
Manual 2 pages 23.06 Kb

59229-05 A, 9100 specifications

The Q-Logic 9100,59229-05 A is a high-performance networking solution designed to empower data centers and enterprise environments with optimal connectivity and exceptional throughput. As an essential component in modern IT infrastructures, this product stands out due to its advanced feature set and robust technology.

One of the main features of the Q-Logic 9100,59229-05 A is its support for Fibre Channel technology, which is widely recognized for its reliability and speed in storage area networks (SANs). This networking solution facilitates seamless data transfer at high rates, significantly enhancing the performance of storage systems.

Another notable characteristic of the Q-Logic 9100,59229-05 A is its compatibility with various operating systems and virtualization platforms. This versatility allows organizations to integrate it easily into their existing infrastructure, ensuring a smooth transition and minimal downtime. The product also supports multiple protocols, enhancing its utility in diverse environments.

The Q-Logic 9100,59229-05 A employs cutting-edge technologies such as offload capabilities, which reduce CPU overhead, allowing servers to focus on critical applications. By offloading certain tasks from the server's main processor, this solution improves overall system performance and efficiency, aiding in quicker data processing and reduced latency.

Additionally, security features embedded within the Q-Logic 9100,59229-05 A help safeguard sensitive information as it traverses networks. It supports encryption and secure data transportation protocols, ensuring that corporate data remains protected against unauthorized access and breaches.

The adaptability of the Q-Logic 9100,59229-05 A is further exhibited through its support for multiple speeds, allowing organizations to choose the bandwidth that best fits their current needs while maintaining the potential for future upgrades as demands grow.

In conclusion, the Q-Logic 9100,59229-05 A not only excels in speed and performance but also offers a versatile and secure solution suitable for a wide range of data center applications. Its blend of advanced features, robust technology, and adaptability positions it as a valuable asset for organizations looking to enhance their network connectivity and storage capabilities in an increasingly data-driven world.