US
the pump body/bodies into the slot/s in the upper basket. Arrange other breast pump components as shown.
2.Place remaining components of the pump in the lower basket.
3.Up to six 4 oz / 125 ml or 9 oz / 260 ml bottles
(not including screw rings, nipples or dome caps) can be sterilized with the pump.
4.Follow sterilizing instructions.
To load the AVENT Tempo Natural Feeding Nurser
Before each use, wash items to be sterilized in mild, soapy water, and rinse.
1.Open the inner locking ring of the screw ring and place the screw ring in the basket with the locking tab facing downwards. Ensure that the parts of the screw ring that are in contact with the nipple are facing upwards.
2.Place the nipple and the dome cap in the basket as you would when sterilizing a bottle assembly.
3.Follow sterilizing instructions.
To remove sterilized items during or after a cycle
1.Let the sterilizer cool down for 3 minutes after sterilizing cycle has been completed.
2.Press the control button to reset (Mode 1) or pause (Mode 2) the unit.
3.Wash your hands thoroughly before removing the sterilized items.
4.Remove the lid.
5.If necessary, shake excess water from items before assembling.
6.The tongs can be used to remove small items and to pull the sterile nipples through the screw rings of the bottles.
7.Removed items must be used/assembled immediately or
8.In Mode 1, the sterilizer must be left to cool for at least 10 minutes between each use.
9.In Mode 2 – items can be removed/replaced and then the cycle restarted. To restart, press the control button. The unit will immediately enter a new sterilization phase and continue the 24 hour cycle from where it was interrupted. If unplugged the countdown cycle will stop.
Dishwasher Basket (see diagram F)
1.Two baskets can be clipped together to hold small items such as nipples, breast pump parts etc. for washing in the top rack of your dishwasher prior to sterilization.
2.To clip together, align the baskets so that the indicators are opposite each other and snap the baskets together. To open, pull apart
with fingers.
Warning: Your Philps AVENT items may discolor over time if they are washed in the dishwasher with dirty items covered with remnants of strong sauces, such as tomato sauce.
Care of your sterilizer
Using distilled water in your iQ24 Sterilizer can reduce limescale build up. You should
Pour 100 ml vinegar mixed with 200 ml cold water into the sterilizer. Allow to stand in the unit until any limescale has dissolved. Drain and rinse the inside of the sterilizer thoroughly. Wipe dry.
Limited Guarantee
Philips AVENT guarantees that the iQ24 Sterilizer be free from manufacturers defects for 12 months from the date of purchase. In the event of a defect, Philips AVENT will repair or replace such parts free of charge with proof of purchase. The iQ24 Sterilizer must be used according to the instructions. The claim must not be a result of a accident, misuse, dirt, neglect or normal wear and tear. For questions about this product or our guarantee please call Customer Service at 1.800.54.AVENT.
Philips AVENT is here to help
For our complete catalog of mother and baby care products and breastfeeding information Call
MANUFACTURED FOR: PHILIPS DOMESTIC APPLIANCES AND PERSONAL CARE COMPANY, A DIVISION OF PHILIPS ELECTRONICS NORTH AMERICA CORPORATION. 1600 SUMMER STREET, 5 FL. STAMFORD, CT
US
Electronic Display Guide
Sterilizer plugged in and ready for mode selection
BEEP | BEEP |
Ready for Mode 1 selection | Ready for Mode 2 selection |
BEEP | BEEP |
Mode 1 sterilization in progress – indicated | Mode 2 sterilization in progress – indicated by a |
by a beep and rotating ‘0’ | beep and three ascending and descending bars |
Numerical countdown indicates sterilization almost complete*
BEEP
X 5
Sterilization complete – indicated by 5 beeps and three flashing bars
– items will remain sterile for up to 6 hours provided the lid is not opened
Up to 6 hours sterile | Up to 4 hours sterile | Up to 2 hours sterile |
time remaining | time remaining | time remaining |
|
|
|
BEEP
Mode 1 cycle (6 hours)
Completion of Mode 2 cycle (24 hours) – indicated by a long beep and a flashing ‘0’
BEEP
Water level too high. See ‘Troubleshooting’ on back cover
BEEP
Water level too low. See ‘Troubleshooting’ on back cover
6 | * Mode 1 only |
7 |