Peg-Perego P3 manual Customer Service, Instructions for USE

EN•ENGLISH

•IMPORTANT: read these instructions carefully and keep them for future reference.

Failure to follow these instructions could put the childʼs safety at risk.

•PEG PEREGO reserves the right to make any necessary changes or improvements to the products shown at any time without notice.

CUSTOMER SERVICE

If parts of the model are accidentally lost or damaged, use only original Peg Perego spare parts. Contact the Peg Perego Customer Service for all repair work, replacements, information about products, and sale of original spare parts and accessories, at the following:

CANADA:

tel.: 905.839.3371

fax: 905.839.9542

Call us toll free: 1.800.661.5050

www.pegperego.com

INSTRUCTIONS FOR USE

OPENING

1• Before opening the stroller remove the two protective caps from the hooks as shown in the figure. Otherwise, the stroller will not open correctly.

2• To open the stroller, pull up the two levers on the handles and

3• at the same time, lift the stroller, which will open automatically. To make sure that the stroller has been set up correctly, check the two side hooks (see figure).

ASSEMBLYING THE STROLLER

4• To mount the front wheels, lower Lever A and slip the wheels onto the axle, as shown in the figure. Press until the wheels click into place.

5• To assemble the rear wheels fasten the wheels connected by the break wire, as indicated in the figure.

6• Carefully distinguish the left wheel from the right, to fasten the two rear wheels properly. The left wheel has a rib on the wheel tube and one on the chassis to guarantee proper fastening (see figure).

7• Make sure that it is fastened properly, as indicated in the figure (click).

8• To mount the basket, slide the slots onto the front hooks A and the rear hooks B and C.

9• The figure shows the mounted basket. 10• The drink-holder can be attached to the

left or the right handle of the stroller, using the two bands.

• To mount the drink-holder to the handle, widen the clamp and fasten as shown in the figure.

11• Slide the clamp in the drink-holder until it clicks.

Do not put hot drinks in the drink-holder, nor items weighing more than 1 kg (2.2 lbs).

FRONT BAR

12• The stroller comes with caps on the armrests. To attach the front bar, remove the caps first. (Keep the caps, in case you want to use the stroller without the front bar). To remove the caps, press the buttons under the armrests while pulling the caps off.

13• To mount the front bar, press the buttons while slipping the front bar onto the armrests, as shown in the figure. Push until the armrest clicks into place. The armrest will now be in the second position (2).

14• To place the front bar in the first position (1), press the buttons under the armrests while pushing the front bar towards the stroller.

15• To remove the front bar, press the two buttons under the armrests while pulling the front bar out. (The front bar will click into the second position). Press the buttons again, and pull the front bar off the stroller. The front bar can be opened on one side only to allow the child to get in and out of the stroller more easily when he is older.

BRAKE

16• To apply the brakes, push down with one foot the bars on the rear wheels, as shown in the figure. To release the brakes, draw the bar up. Always set the brakes on the stroller when it is not in motion.

SAFETY BELT

17• A: Make sure that the brace is properly inserted by pushing as shown in the figure. B: Fasten the belt as shown in the figure.

18• To unfasten the belt, press on the buckle sides and pull out the waist strap.

19• The new safety belt is now easier to fasten thanks to the "snap-open-and- shut" device. Before fastening the safety belt, attach the buckle to the backrest by inserting the tab through the special holder, as shown in the figure. After fastening the safety belt on your child, detach it from the backrest to allow the child more freedom of movement. The buckle must remain below the child's shoulders.