Britax Roundabout manual Pounds, Disconnect the Versa-Tetherfrom the tether anchor, Slots. See

Page 11

Installation: Forward-Facing

Installation: Forward-Facing

LATCH Installation

•Figure A illustrates a typical forward-facing LATCH installation.

•Verify that your vehicle is equipped with LATCH anchors. If LATCH anchors are not available, you must use vehicle belt installation methods.

WARNING! This child seat must not be used forward-facing for children less than one year of age OR weighing less than

20 pounds.

1￿ If stored, remove LATCH connectors from storage slots under cover. See page 30. Pull both connectors completely through the child seat’s right-side, rear-facing belt slot (Fig. B) so they are on the outside of the shell.

2￿ Press each LATCH adjuster release button and pull each LATCH adjuster strap to full length.

3￿ Thread the LATCH connectors through forward-facing belt path (Fig. C) to the back of the child seat.

NOTE: It may be necessary to switch LATCH connectors as shown on page 29 if ANY of the following conditions exist:

•LATCH connector is not in an upright position as shown in figure D.

•LATCH strap is twisted.

•A positive click is NOT heard when LATCH connector and LATCH anchor are connected.

A Forward-Facing

B

C

Release Top Button

D

4￿ Place the child seat sideways on the vehicle seat, with the back facing you.

•Child seat may be in upright or recline position. See Recline Adjustment on page 30.

5￿ Remove the Versa-Tether®from pouch and place up and over the child seat back.

6￿ Verify that the LATCH strap is not twisted and E attach the closest LATCH connector to the vehicle seat back to the farthest LATCH anchor (Fig. E).

• A positive click confirms attachment.

7￿ Rotate the child seat into the forward-facing position.

8￿ Verify that the LATCH strap is not twisted and attach the remaining LATCH connector to the F adjacent LATCH anchor (Fig. F).

• A positive click confirms attachment.

9￿ Push the child seat into the vehicle seat while

 

pulling each LATCH adjuster strap tight (Fig. G).

 

10￿Attach the Versa-Tether®hook to an approved

 

tether anchor. Remove all slack from the tether

G

to secure. Store excess webbing in the tether

pouch. See pages 25 – 28.

 

11￿Verify all connections are secure and that the child seat is secure.

•The child seat is secure when it cannot be moved front-to-back or side-to- side more than 1 inch (2.5 cm.) at the belt path.

Removal

• Disconnect the Versa-Tether®from the tether anchor.

• Release each LATCH harness from the LATCH anchor by pressing

NOTE: If a positive click is not heard, but the LATCH connector is in an upright position, you should not switch the LATCH connector. The strap may be too tight or twisted, or there may be debris in the LATCH connector.

the red release button on the LATCH connector.

• When not in use, always store the LATCH connectors in storage

slots. See page 30.

18

19

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Roundabout Table of Contents Page Registration Important NotesCertification Do not use the child seat forward-facing if Important Harness AdjustmentsForward-Facing Rear-FacingChild Seat Features Vehicle Seating Positions Vehicle Safety BeltsCannot be used. See diagram below Vehicle Buckle PositionsRemoval Latch InstallationPerform as intended Lap-Shoulder Belt Installationfirst rear-facing belt slot Fig. C Then close the lock-off arm Fig. E and replace the cover Lap-Belt InstallationFacing on vehicle seat Seat while removing slack from the vehicle beltSlots. See Red release button on the Latch connectorPounds Disconnect the Versa-Tetherfrom the tether anchorLock-off upward until secured Fig. E Lap-Belt Installation Forward-Facing Installation Aircraft InstallationSafety Information Rear-Facing InstallationSecure the child seat by a seat-belt or Using the Versa-TetherTether Connector Strap With the Latch connectorsChild seat is necessary Switching the Latch ConnectorsEnergy-Absorbing Tether Harness Buckle Storing the Latch ConnectorsRecline Adjustment Chest ClipSecuring Your Child How to Adjust Harness Slot HeightChild Seat Cover Removal Sponge Clean using warm water and mild soapFully recline the child seat Cleaning the Harness BuckleHarness Buckle Removal Re-threading the Harness BuckleWarranty Double Check Child-to-Car Seat Installation Double Check Car Seat-to-Vehicle Installation

Roundabout specifications

The Britax Roundabout is a well-regarded convertible car seat that exemplifies safety, comfort, and convenience for parents and children alike. Designed to accommodate children from approximately 5 to 65 pounds, it provides a versatile seating solution suitable for infants and toddlers as they grow.

One of the standout features of the Britax Roundabout is its dual mode functionality, allowing it to function as both a rear-facing and forward-facing car seat. This flexibility enables parents to keep their child in the safer rear-facing position for as long as possible, which is highly recommended by safety experts. The Roundabout easily transitions to forward-facing once the child surpasses the appropriate weight and height limits, making it a long-lasting investment.

Safety is paramount with the Britax Roundabout, which is equipped with innovative technologies designed to enhance protection during a collision. The seat incorporates Britax's SafeCell Impact Protection system, featuring a base that compresses to reduce the impact of a crash and protect the child’s head, neck, and spine. Additionally, the seat comes with side impact protection, which provides extra security in the event of a side collision.

Comfort is also a key aspect of the Roundabout's design. The seat features plush, padded fabric to ensure a cozy ride for your little one. The seat cover is also easy to remove and machine washable, providing convenience for parents when it comes to cleaning up spills and messes.

Installation of the Britax Roundabout is designed to be straightforward and user-friendly. It is equipped with the ClickTight Installation System, which allows for easy and secure installation using the vehicle's seat belt or LATCH system. This technology minimizes the risk of installation errors, which are common with other car seats.

Other notable characteristics include multiple recline positions for added comfort during long journeys and a 5-point harness system that ensures a secure fit for children of different sizes. The Roundabout is also known for its durable construction, which contributes to its longevity and reliability.

In summary, the Britax Roundabout is a convertible car seat that stands out due to its combination of safety features, user-friendly installation, and comfort. As children grow, the Roundabout adapts to their needs, making it a practical choice for parents seeking a dependable and versatile car seat for their family.
Top Page Image Contents