Graco DR5, DS5, D82, D72, D85, DR2, DS2, D81, D75 Grounding, Ground all of this equipment

Page 5

Installation

Grounding

WARNING

FIRE AND EXPLOSION HAZARD This pump must be grounded. Before operating the pump, ground the system as explained below. Also read the sec- tion FIRE AND EXPLOSION HAZARD on page 3.

The acetal pump contains stainless steel fibers which make the wetted parts conductive. Attaching the ground wire to the grounding screw will ground the air motor and the wetted parts.

The polypropylene and PVDF pumps are not conductive. Attaching the ground wire to the grounding screw will ground only the air motor. When pumping conductive flammable fluids, al- ways ground the entire fluid system by making sure the fluid system has an electrical path to a true earth ground (see Fig. 2). Never use a poly- propylene or PVDF pump with non-conductive flammable fluids as specified by your local fire protection code.

US Code (NFPA 77 Static Electricity) recommends a conductivity greater than 50 x 10–12Siemans/me- ter (mhos/meter) over your operating temperature range to reduce the hazard of fire. Consult your fluid supplier to determine the conductivity or resistivity of your fluid. The resistivity must be less than 2 x 1012 ohm-centimeters.

Ground all of this equipment:

DPump: Connect a ground wire and clamp as shown in Fig. 1. Loosen the grounding screw (W). Insert one end of a 12 ga (1.5 mm@) minimum ground wire

(Y) behind the grounding screw and tighten the screw securely. Connect the clamp end of the ground wire to a true earth ground. Order Part No. 222011 Ground Wire and Clamp.

NOTE: When pumping conductive flammable fluids with a polypropylene or PVDF pump, always ground the entire fluid system. See the WARNING left. Fig. 2 shows a recommended method of grounding flam- mable fluid containers during filling. This is only a guide; contact your Graco distributor for assistance in grounding your system.

Y

W

To reduce the risk of static sparking, ground the pump and all other equipment used or located in

Fig. 1

02646B

the pumping area. Check your local electrical code for detailed grounding instructions for your area and type of equipment.

DAir and fluid hoses: Use only grounded hoses with a maximum of 500 ft (150 m) combined hose length to ensure grounding continuity.

DAir compressor: Follow the manufacturer’s recom- mendations.

DAll solvent pails used when flushing: Follow the local code. Use only grounded metal pails, which are conductive. Do not place the pail on a non-con- ductive surface, such as paper or cardboard, which interrupts the grounding continuity.

DFluid supply container: Follow the local code.

308443 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Huskyt1040 Air-Operated Diaphragm Pumps Instructions Parts ListSymbols Table of ContentsToxic Fluid Hazard Tightening Screws Before First Use InstallationGeneral Information Ground all of this equipment GroundingAir Line Floor Mount Typical InstallationMountings Installation of Remote Pilot Air LinesFluid Suction Line Fluid Outlet LineBolt Tightening Sequence Flange ConnectionsFluid Pressure Relief Valve Changing the Orientation of the Fluid Inlet and Outlet PortsVenting Exhaust AIR Air Exhaust VentilationFire and Explosion Hazard Starting and Adjusting the Pump Pressure Relief ProcedureOperation Flush the Pump Before First UsePump Shutdown Operation of Remote Piloted PumpsPreventive Maintenance Schedule MaintenanceLubrication Tightening Threaded ConnectionsProblem Cause Solution TroubleshootingTroubleshooting Repairing the Air Valve ServiceReassembly Ball Check Valve Repair Diaphragm Repair Service 19 402 105 104 401 403 Bearing and Air Gasket Removal Detail of Air Valve Bearings Stainless Steel Air Motor Conversion Kit Pump MatrixHusky 1040 Acetal, Polypropylene, and Pvdf Pumps, Series a Repair Kit Matrix Parts Digit Description Qty Air Motor Parts List Matrix ColumnMuffler Fluid Section Parts List Matrix ColumnDiaphragm Parts List Matrix Column Seat Parts List Matrix ColumnBall Parts List Matrix Column Torque Sequence Side View Pump Mounting Hole Pattern InDimensional.DrawingsFront View Technical Data Fluid Pressure Curves Performance ChartGraco Information Graco Warranties

D75, D81, D85, DS5, DS2 specifications

Graco is a well-known name in the world of spray equipment and fluid management systems, and its range of airless sprayers like the D82, DR2, DR5, D72, and DS2 exemplifies innovation and quality. These models are engineered to meet the diverse needs of professional painters, contractors, and DIY enthusiasts alike.

The Graco D82 is designed for high-performance applications, delivering consistent spray patterns and superior coverage. One of its standout features is the ProConnect system, which allows users to quickly change pumps on the job site, minimizing downtime. Its SmartControl technology ensures a consistent spray pattern at any pressure, allowing for versatility across a range of coatings. Its lightweight, portable design also makes it an ideal choice for jobs of all sizes.

Moving on to the DR2, this model boasts two-piston technology which provides a reliable and powerful performance. It is specifically engineered for working with thicker materials, making it perfect for heavy coatings like elastomerics or textured paints. The DR2's integrated filtration system protects the pump from debris, prolonging its life and ensuring cleaner finishes.

The Graco DR5 takes it a step further by offering a robust solution for contractors working on large-scale projects. This model includes Graco's Endurance pump which is known for its durability and performance longevity. The DR5 features an ergonomic design that enhances user comfort during extended use, while its heavy-duty build can withstand the rigors of demanding job sites.

Next in line is the D72, which offers an efficient spraying solution for both interior and exterior applications. It comes equipped with Graco’s easy-to-use controls and an extended reach design that makes it suitable for large projects. The D72 also integrates advanced technology for automatic pressure adjustment, ensuring optimal spray results regardless of the conditions.

Lastly, the DS2 is a compact yet powerful sprayer suited for smaller projects or tight spaces. This model delivers professional-grade results without the bulk. It features a user-friendly interface that makes it accessible for beginners while still providing the performance features necessary for seasoned professionals.

In summary, the Graco D82, DR2, DR5, D72, and DS2 each bring their own unique advantages to the table. From advanced technologies like ProConnect, SmartControl, and Endurance pumps to user-friendly designs, these models represent Graco's commitment to providing high-quality spray solutions that cater to the diverse needs of their users. Whether for heavy-duty applications or smaller projects, Graco's lineup offers a comprehensive range of options for effective and efficient painting.
Top Page Image Contents