Dantax LR-8500 manual Surround back speakers, Subwoofer

Page 7

Connections

Surround back speakers

Surround back speakers are required when a full 7.1-chan- nel system is installed.

Speakers should be placed on a rear wall, behind the lis- tening position.

The center of the speaker should face into the room.

Subwoofer

We recommend using a subwoofer to have maximum bass effect. Subwoofer bears only low frequency range so you can place it any where in the room.

HEIGHT OF THE SPEAKER UNITS

Front left and right speakers, and a center speaker

Align the tweeters and mid-range drivers on the three front speakers at the same height, as best as possible.

Surround left and right speakers, and surround back speaker

Place the surround left, right and surround back speakers higher than your ears by about 70cm -1m.

Also place the speakers at the same height, as best as pos- sible.

70cm

1m

Note:

•Use magnetically-shielded speakers for front left, right and the center speakers when the speakers are installed near the TV and the TV is a monitor type.

CONNECTING SPEAKER WIRE

1.Strip away approx. 10 mm of wire insulation.

2.Twist the bared wire ends tight, to prevent short circuits.

3.Loosen the knob by turning it counterclockwise.

4.Insert the bare part of the wire into the hole in side of each terminal.

5.Tighten the knob by turning it clockwise to secure the wire.

1.2.

10mm

3.4. 5.

Caution:

•Be sure to use speakers with the specified impedance as shown on the rear panel of this unit.

•To prevent damage to circuitry, do not let the bare speak- er wires touch each other and do not let them touch any metal part of this unit.

•Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks.

•Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit.

Note:

•Be sure to connect the positive and negative cables for the speaker properly. If they are miss connected, the sig- nal phase will be reversed and the signal quality will be corrupted.

CONNECTING A SUBWOOFER

Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifier built in ).

If your subwoofer is a passive type (power amplifier is not built in), connect a monaural power amplifier to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifier.

- 7 -

Page 6 Page 8
Image 7
Page 6 Page 8
Contents LR-8500 If in Doubt Consult a Competent ELECTRI- Cian Important Safety InstructionsIMPORTANTfor U.K.Customers Blue Neutral Brown LiveTable of Contents Back-up Memory Function When to Use ResetBefore Use Read this before operationNeo6 offers several important improvements as follow DescriptionCenter speaker Description ConnectionsAbout Dolby Pro Logic Front left and right speakersSurround left and right speakers, and surround back speaker Surround back speakersSubwoofer Front left and right speakers, and a center speakerPRE OUT SUB Woofer jack Power cord AC InputRS-232C Audio Components Video convert There are 3 types of video jacks on the rear panelVideo jack Component jackVideo Components and Advanced Connecting Supplied AM loop antenna is for indoor use only Connecting the supplied FM antennaConnecting the supplied AM loop antenna Supplied FM antenna is for indoor use onlyFront Panel Control FunctionsTV / VID Display Remote Control UnitPower TEST-TDirection Tuning UP/DOWNPreset UP/ Down TOP MenuZone II Remote Control Unit TUN-M Source Select Volume STANDBY/ON Menu EnterControl Functions Basic Operations Input SelectorsPress to select input sources Volume knobSurround Mode Selector Sleep Timer FunctionOFF Surround Mode Night ModeMAX MIDII Audio Outputs Zone II OperationSize of Speakers Speaker ConfigurationInput the distance from your listening position Balancing relative volume between speakers using Test ToneTuner-Mode Preset MemoryTuner Operation Station SelectionCT Clock Time RDS Radio Data System Remote Controller OnlyPS Program Service Name PTY Program TypeVideo Tape Dubbing System Configuration OSD On Screen DisplayMaking Configuration Adjustments Video OperationsFunction Setup System ConfigurationFunction Setup Surround SetupDolby Surround Dolby SurrUpsampling Speaker Setup CH Level Adjust Distance AdjustPreference Setup Back to Main Menu Zone II SetupRoom Auto Setup Check all speaker wire connections and then rerun ErrorCode Check Method Controlling other Components Connected to the LR-8500Direct Code Entry Method Manual Search MethodVCR Brand List Programming the RemoteSAT Brand List TV Brand List Erres Pathe Cinema Troubleshooting PAL / Ntsc SpecificationsOutput Power DTSLuxman CORPORATION, Japan

LR-8500 specifications

The Dantax LR-8500 is an impressive entry in the realm of audio engineering, known for its advanced capabilities and high-quality sound reproduction. This versatile device caters to both audiophiles and casual listeners alike, making it a significant player in the industry.

One of the standout features of the Dantax LR-8500 is its powerful amplification system. With a robust power rating, it delivers clear, dynamic sound that encapsulates every nuance of the audio spectrum. The amplifier is designed to handle a wide range of speaker impedances, making it compatible with various setups without sacrificing audio quality. This flexibility allows users to tailor their listening experience to their specific preferences.

The LR-8500 is equipped with a range of connectivity options that prioritize convenience and versatility. Users can enjoy seamless wireless connectivity with Bluetooth capabilities, allowing them to stream music directly from smartphones, tablets, and other devices with ease. Additionally, multiple inputs, including optical and coaxial connections, are available, ensuring compatibility with other audio sources such as TVs, gaming consoles, and CD players.

Incorporating cutting-edge technologies, the Dantax LR-8500 features advanced digital signal processing (DSP). This technology enhances sound quality by optimizing audio performance for different genres and environments. Users can choose from various preset modes, enabling them to enjoy a tailored sound experience whether they’re listening to music, watching movies, or playing video games.

The design of the LR-8500 reflects a commitment to both aesthetic appeal and functionality. The sleek, modern look fits seamlessly into any home décor while providing intuitive controls for easy operation. The illuminated display screen offers clear visibility, making it simple to navigate settings and features, even in low light.

Moreover, the Dantax LR-8500 is energy-efficient, ensuring that high performance does not come at the expense of excessive power consumption. This consideration demonstrates Dantax's commitment to sustainability while providing users with a premium audio experience.

In conclusion, the Dantax LR-8500 stands out due to its robust features, modern technology, and elegant design. Ideal for a range of users, it embodies the perfect blend of quality, performance, and versatility in the competitive audio market. Whether for casual enjoyment or serious listening sessions, the LR-8500 offers an audio experience that is hard to match.
Top Page Image Contents