Canon N656U, N1220U, N650U manual Click on the OK button, Shadow Mark

Page 39

S T E P 3

The histogram settings can be adjusted for all channels (Master) or for individual channels (R, G, B). The selectors are displayed to the left of the histogram graph (Master, R, G, B). The Master selection is unavailable if Grayscale has been selected as the scan mode.

Shadow Mark

Clicking directly on this bar causes the shadow or highlight

mark, whichever is closest, to advance to that position.

All of the data to the

left of this mark is set

Highlight Mark

to the shadow (0)

All of the data to the

value. Drag the mark

to the right or left.

right of this mark is set

to the highlight (255)

Displays the current

value. Drag the mark

to the right or left.

level at the shadow

mark. Click the up or

Displays the current

down arrows in the

spinbox to increase or

level at the highlight

decrease the setting or

mark. Click the up or

enter a number directly

down arrows in the

into the entry box

spinbox to increase or

(0~254).

decrease the setting or

enter a number directly

To restore the histogram

into the entry box

settings, click this

(1~255).

[Reset] button.

The Tone Adjustment

To restore all settings

settings can be saved

to their defaults, click

in a file and reloaded

the [All Reset] button.

for later use.

Black Eyedropper Button

White Eyedropper Button

Auto Button

Click the Black Eyedropper

Automatically sets

Click the White Eyedropper

and click the position in the

the highlight and

and click the position in the

preview image you want to

shadow settings for

preview image you want to

set to black (0).

optimum effects.

set to white (255).

Click on the [OK] button.

The preview image will change according to the values specified with the histogram.

Hint

• The histogram dialog can also be displayed by selecting [Tone Adjustment] from the [Image] menu.

39

Image 39

Contents Users Guide When you open the box How to Make Best Use of the ManualsHow to Use this Guide Where to LookAbout the Conventions Used in this Guide Table of Contents Adjusting Scanned Images Operating Environment Installing Plug-in Module CS-UImage Size pp Control Panel FeaturesE P Scanning ProceduresColorSync Ver 2.0 + Compatible for Auto Tone Correction Plug-in Module CS-U Special FeaturesSee the Results of Adjustments Immediately Dynamic Preview Gamma Curve Adjusts Image BrightnessPosition materials for scanning and preview them Install Plug-in Module CS-UQuick Start Instructions Start Plug-in Module CS-USelect the area to be scanned by clicking and dragging Verify Image Quality with the Browser Function beforeSpecify the Area of the Image to be Scanned Click on the Browser button Selection frame will appearSave the Scanned Image p Scan the Image pE P RGB Values Displaying the Plug-in Module CS-U Control PanelOperating Procedures Procedures Positioning OriginalsPlace the original on the scanners document glass Click on the Preview button PreviewingSelecting the Output Device Output Device Resolution= 720 dpi, Magnification= 100% Setting the Resolution and MagnificationSet the desired magnification factor on the control panel To Set the Magnification FactorColor Documents Setting the Scan ModeBlack and White GrayscaleSelect a scan mode from the pop-up menu Click the arrow beside Scan ModeTo Verify the Image Verifying the Image before ScanningUse these buttons to rotate the image Rotating the ImageSetting Preferences Output DeviceAspect Ratio Preview Window UnitReset Default Settings CalibrationClose Plug-in After Scan Operating Procedures Scanning Position the pointer in the preview window Setting the Scan AreaProcedures to Zoom ZoomingSelect the area you want to enlarge with the zoom function Click on the Zoom In button Click on the Scan button ScanningTo Initiate the Scan Specify the Scan AreaEnter a name for the file and click the Save button Saving Scanned ImagesGrayscale, Color Photos and Color Documents Black & WhiteColor Photos and Color Documents Tone Adjustment Dialog Tone AdjustmentHow to Interpret Histograms Histogram SettingsHow to Adjust Histograms To Adjust a HistogramShadow Mark Click on the OK buttonManipulating the Graph Tone Curve SettingsClick the OK button To Edit the Tone CurveValue = Relationship Between the Tone Curve Image BrightnessBrightness and Contrast Settings ContrastBrightness To Adjust the Brightness and Contrast Operating Procedure Adjusting the Color BalanceGamma Value Settings Matching the Gamma Value to the Display CharacteristicsGamma value To Change the Gamma Value Settings To Set the Threshold Value Adjusting the Threshold ValueColorSync Auto Tone CorrectionTo Set the Auto Tone Correction StandardOpen the Image menu and select Unsharp Mask Unsharp MaskOpen the Image menu and select Descreen DescreenSaving/Recalling Settings To Save Settings in a Settings FileClick the Save button To Recall a Settings File Matching Scan Resolution to Purpose Optical and Enhanced ResolutionsScanning Techniques Appendices Troubleshooting Problem Scan button cannot be selected Response Error MessagesError Message CauseBlack Eyedropper Tool GlossaryAuto Tone Correction Bits/Bit NumbersDot Color ChannelHistogram Image FileMagnification Pixel Optical ResolutionResolution MoiréTone Curve Scan ModeShadows Threshold ValueOutput device 7, 11, 18, 25 IndexPage Canon Computer SYSTEMS, INC Canon Customer Support Help DeskOE-040AA 052000 CDS Canon Inc