Canon N1220U, N656U, N650U manual Error Messages, Cause, Response

Page 58

Error Messages

Error Message

Scanner is not connected. Connect the scanner.

Scanning unit is locked. Release the lock switch at the base of the scanner and connect the PC to the scanner again.

Sensor type error. Please get a new driver.

1)Cannot complete scan command. Insufficient memory (RAM).

2)Memory is insufficient. Increase the memory allocated the application.

As image size is large, it will take long to complete scanning. Do you want to continue?

An error has occurred. Error Code =** Restart the PC.

Cause

USB cable not connected correctly.

The scanning unit lock not released.

The scanning unit is out of order.

Old version of driver software detected.

Memory is insufficient for the required volume of the scanned image data.

You attempted to scan an image exceeding 100 MB.

Scanner or computer is malfunctioning.

Response

Use the USB cable to connect the Macintosh to the scanner properly.

After releasing the lock, temporarily disconnect the USB cable. Reconnect it and restart Plug-in Module CS-U.

Contact your nearest Canon

Customer Support Help Desk.

Download and install the latest driver software.

Reduce the scan area to the minimum possible scope and lower the resolution and magnification settings for the output device.

Close all application programs other than the one used to start Plug-in Module CS-U.

Increase the memory allocated to the application program used to start Plug-in Module CS-U.

Click [Cancel] to cancel, or rescan after lowering the scanning resolution or reducing the scanning area.

Restart the computer.

If the same error code displays after restarting the computer, contact the nearest Canon

Customer Support Help Desk.

58

Image 58
Contents Users Guide How to Make Best Use of the Manuals When you open the boxWhere to Look How to Use this GuideAbout the Conventions Used in this Guide Table of Contents Adjusting Scanned Images Installing Plug-in Module CS-U Operating EnvironmentControl Panel Features Image Size ppScanning Procedures E PGamma Curve Adjusts Image Brightness Plug-in Module CS-U Special FeaturesSee the Results of Adjustments Immediately Dynamic Preview ColorSync Ver 2.0 + Compatible for Auto Tone CorrectionStart Plug-in Module CS-U Install Plug-in Module CS-UQuick Start Instructions Position materials for scanning and preview themClick on the Browser button Selection frame will appear Verify Image Quality with the Browser Function beforeSpecify the Area of the Image to be Scanned Select the area to be scanned by clicking and draggingScan the Image p Save the Scanned Image pE P Displaying the Plug-in Module CS-U Control Panel RGB ValuesOperating Procedures Positioning Originals ProceduresPlace the original on the scanners document glass Previewing Click on the Preview buttonSelecting the Output Device Setting the Resolution and Magnification Output Device Resolution= 720 dpi, Magnification= 100%To Set the Magnification Factor Set the desired magnification factor on the control panelGrayscale Setting the Scan ModeBlack and White Color DocumentsClick the arrow beside Scan Mode Select a scan mode from the pop-up menuVerifying the Image before Scanning To Verify the ImageRotating the Image Use these buttons to rotate the imageOutput Device Setting PreferencesAspect Ratio Unit Preview WindowCalibration Reset Default SettingsClose Plug-in After Scan Operating Procedures Scanning Setting the Scan Area Position the pointer in the preview windowZooming Procedures to ZoomSelect the area you want to enlarge with the zoom function Click on the Zoom In button Specify the Scan Area ScanningTo Initiate the Scan Click on the Scan buttonSaving Scanned Images Enter a name for the file and click the Save buttonBlack & White Grayscale, Color Photos and Color DocumentsColor Photos and Color Documents Tone Adjustment Tone Adjustment DialogHistogram Settings How to Interpret HistogramsTo Adjust a Histogram How to Adjust HistogramsClick on the OK button Shadow MarkTone Curve Settings Manipulating the GraphTo Edit the Tone Curve Click the OK buttonRelationship Between the Tone Curve Image Brightness Value =Contrast Brightness and Contrast SettingsBrightness To Adjust the Brightness and Contrast Adjusting the Color Balance Operating ProcedureMatching the Gamma Value to the Display Characteristics Gamma Value SettingsGamma value To Change the Gamma Value Settings Adjusting the Threshold Value To Set the Threshold ValueStandard Auto Tone CorrectionTo Set the Auto Tone Correction ColorSyncUnsharp Mask Open the Image menu and select Unsharp MaskDescreen Open the Image menu and select DescreenTo Save Settings in a Settings File Saving/Recalling SettingsClick the Save button To Recall a Settings File Optical and Enhanced Resolutions Matching Scan Resolution to PurposeScanning Techniques Appendices Troubleshooting Problem Scan button cannot be selected Cause Error MessagesError Message ResponseBits/Bit Numbers GlossaryAuto Tone Correction Black Eyedropper ToolColor Channel DotImage File HistogramMagnification Moiré Optical ResolutionResolution PixelThreshold Value Scan ModeShadows Tone CurveIndex Output device 7, 11, 18, 25Page Canon Customer Support Help Desk Canon Computer SYSTEMS, INCOE-040AA 052000 CDS Canon Inc