Yamaha YSP-3000 owner manual Auto Setup Start, 39 En, BEAM+SOUND Optimz

Page 41

 

 

AUTO SETUP (IntelliBeam)

 

 

 

5 Press / to select BEAM+SOUND

 

6 Check the following points once again before

OPTIMZ, BEAM OPTIMZ only, or SOUND

 

starting the AUTO SETUP procedure.

OPTIMZ only and then press ENTER.

 

• Is the IntelliBeam microphone firmly connected to

The following screen appears on your TV.

 

this unit?

• Is the IntelliBeam microphone placed in a proper

 

location?

ENTER

• Are there any large obstacles in between the

IntelliBeam microphone and the walls in your

ENTER

 

 

listening room?

 

7 Press ENTER to start the AUTO SETUP

 

procedure.

AUTO SETUP

PREPARATION & CHECK Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from the YSP unit. The MIC should be set at ear level when seated. Measurement takes about 3min. After [ENTER] is pressed, please leave the room. [ENTER]:Start [RETURN]:Cancel

BEAM+SOUND OPTIMZ

(Beam optimization and sound optimization)

Use to optimize the beam angle, delay, volume, and quality so that the parameters best match your listening environment.

It is recommended that you should select this optimization feature in the following cases:

If you make settings for the first time.

If the unit has been relocated.

If your listening room has been restructured.

If the objects in your listening room (furniture, etc.) have been rearranged.

This menu takes about three minutes.

BEAM OPTIMZ only (Beam optimization only)

Use to optimize the beam angle so that the parameter best matches your listening environment.

This menu takes about one minute.

SOUND OPTIMZ only (Sound optimization only)

Use to optimize the beam delay, volume, and quality so that the parameters best match your listening environment. It is recommended that you should select this optimization feature in the following cases:

If you have opened or closed the curtains in your listening room before using this unit.

If you have manually set the beam angle.

This menu takes about two minutes.

The following screen appears on your TV and the AUTO SETUP procedure starts in 10 seconds. Leave the room quietly before starting the AUTO SETUP procedure.

ENTER

AUTO SETUP START

Will begin in 10sec

 

Please leave the room

Flashes

**--------

 

[RETURN]:Cancel

 

If an error occurs, an error buzzer is played and an error message is displayed. See “Error messages for AUTO SETUP” on page 41 for a complete list of error messages and their proper remedies. Follow the instructions and perform the AUTO SETUP procedure again.

SETUP

Note

You must optimize the beam angle in the BEAM OPTIMZ only procedure before starting the SOUND OPTIMZ only procedure.

English

39 En

Image 41
Contents YSP-3000 For U.K. Customers Contents Overview Features Features Using this manual Check that you have received all of the following parts Supplied accessoriesFront panel Controls and functionsInput STANDBY/ONFront panel display Rear panel 10 En Remote control Europe, Australia, Asia, and Korea models11 En 12 En PRESET/TUNEMemory SearchSound field program buttons Remote control U.S.A. and Canada models13 En CAT 14 EnCursor buttons 15 EnBefore installing this unit InstallationInstalling this unit 16 EnExample Installation examples17 En Using a rack Using a metal wall bracketUsing a stand 18 En19 En Connections20 En Hdmi cable OSD video pin cable Audio Optical cable Connections using Hdmi cables21 En OSD video pin cable Audio pin cable Optical cable Connecting a TV22 En Audio pin cable Digital audio pin cable Connecting a DVD player/recorder23 En Audio pin cable Optical cable Connecting a digital satellite tuner or a cable TV tuner24 En 25 En Connecting a digital airwave tunerMm stereo mini plug cable Connecting a portable audio player26 En Audio pin cable Optical cable Digital audio pin cable Connecting other external components27 En 28 En Connecting a subwooferConnecting the AC power supply cable Connecting the FM antennaAbout the IR in terminal U.S.A. and Canada models only 29 EnOperation range of the remote control Installing batteries in the remote controlClose the battery cover Getting startedPress STANDBY/ON again to set this unit to the standby mode VolumePress STANDBY/ON to turn on the power of this unit 31 En32 En Using SET MenuDisplaying the OSD on-screen display 33 En Flow chart of SET MenuChanging OSD language Language SetupSET Menu 34 En35 En Auto Setup IntelliBeamFlow chart of Auto Setup 36 En Installing the IntelliBeam microphonePress STANDBY/ON to turn off the power of this unit Assembling the supplied cardboard Microphone stand Using Auto Setup IntelliBeam37 En Set the operation mode selector to YSP Auto SetupPress / to select Auto Setup and press Enter 38 EnBEAM+SOUND Optimz Auto Setup Start39 En Check that the following screen is displayed on your TV Show Result40 En Before the Auto Setup procedure starts Error messages for Auto SetupWhile the Auto Setup procedure is in progress 41 EnSaving settings Using the system memory2MEMORY Save MemoryMemory Loading settings43 En Press Enter again44 En 1MEMORY LoadPress / to select Load and press Press Enter again Press / to select MEMORY1Selecting the input source PlaybackTV/STB Auto DVDAUX3 AUX1 AutoPlaying back sources 46 EnAudio Mute Adjusting the volumeDVD 5BEAM Audio Mute OFFRemote control functions FM tuningFM controls and functions 48 En49 En Automatic tuningManual tuning 50 En Automatic preset tuningPress Memory while the Memory indicator Is flashing Manual preset tuning51 En Tune into the desired FM stationPreset station number 1 to Selecting a preset stationA1FM 52 EnTune into the desired Radio Data System broadcasting station 53 EnBeam Enjoying surround sound54 En Press 5BEAM to select 5 Beam55 En Stereo plus 3 BeamMy Surround Input channel indicators Decoder indicators56 En Surround modes and recommended sources57 En Enjoying 2-channel sourcesSurround sound 58 En Press Volume +/- to adjust the volume levelSelect the TV channel you want to watch Press TVWhen Dolby Pro Logic II Music is selected Adjusting surround mode parametersWhen DTS Neo6 Music is selected 59 EnChannel stereo playback Enjoying stereo sound5CH Stereo 60 EnPlaying back sound clearly My Beam Using auto-adjust function61 En Press and hold MY Beam for more than two secondsPress / while MY Beam is displayed to adjust the beam angle Using manual-adjust functionAngle 62 EnWhat is a sound field? Using sound field programs63 En Elements of a sound field64 En Cinema DSP programsMusic program Movie programDSP Level Adjusting Cinema DSP effect levelsCinema DSP 65 EnPress Enhancer to select the Music Enhancer Using the music enhancer66 En NIGHTCINEMA, NIGHTMUSIC, TV Equal 67 En68 En Using the sleep timerUnit to confirm the setting for the sleep timer 69 En Canceling the sleep timerSleep OFF Press Display Displaying the input source information70 En 71 En Using the Hdmi control featureSound Menu 72 EnBeam Menu Input Menu73 En Manual SetupUsing Manual Setup Installed Position Installed position of this unit Setting parameters2BEAM Menu 74 EnHorizontal Angle Horizontal angle Beam Adjustment Beam adjustment75 En Focal Length Focal length 76 EnBeam Travel Length Beam travel length Image Location Image location Cimage Location77 En Atone Control 1SOUND MenuCmute Level 78 En79 En Daudio DelayEroom EQ 3INPUT Menu Binput ModeAinput Assignment 80 EnDinput Rename Hdmi SET Hdmi settingsEhdmi SET 81 EnXM Antenna Level XM antenna level A. and Canada models only FXM Antenna Level82 En AF.DISPLAY SET 4DISPLAY MenuBosd SET Cunit SETUsing the test tone Adjusting the audio balanceTest Front 84 En85 En Using the audio output being played back86 En 87 En Selecting the input modeAuto DTSUsing the system parameters Adjusting the system parametersProtect 88 En89 En Press / to switch between Protect on and Protect OFFProtect OFF Setting the Turn on Volume Setting the MAX VolumeMAX Volume SET Press / to adjust the maximum volume levelSetting the Demo Mode Turn VolumeDemo Mode Press / to adjust the initial volume levelDemo Setting the Panel Input KEYDemo OFF Panel Input KEYInput OFF Press / to switch between P.INPUT on P.INPUT OFFDisabling the front panel keys Panel KEYPanel Setting the Factory PresetPanel OFF Factory95 En Preset Reset PresetcancelPress / to switch between Preset Reset and Preset Cancel Setting remote control codes Remote control features96 En Code SET97 En Controlling other componentsOperating your TV TV INPUT1Operating your DVD player/recorder 98 EnOperating your STB CATV/Satellite tuner Operation buttons for DVD playersOperation buttons for VCR 99 EnOperating your VCR Setting macros for the TV with the tuning capability Using the TV macroPress Enter to confirm the macro setting 100 EnCanceling the macros Setting macros for the TV without the tuning capability101 En Operating macrosGeneral Troubleshooting102 En 103 En Problem Cause RemedyFM tuner Remote control104 En 105 En GlossaryLFE 0.1-channel 106 EnNeural Surround PCM Linear PCMNumerics Index107 En 108 En SpecificationsConditions 109 En

YSP-3000 specifications

The Yamaha YSP-3000 is a revolutionary digital sound projector that has carved a niche for itself in the realm of home theater audio systems. Launched as a versatile sound solution, the YSP-3000 integrates cutting-edge technology to deliver an immersive audio experience that mimics that of traditional multi-speaker surround sound systems.

One of the main features of the YSP-3000 is its unique Digital Sound Projector technology. It utilizes a series of miniature speakers arranged in an array to create a broad sound stage. This allows the YSP-3000 to project sound around the room, simulating the effect of surround sound without the need for additional speakers positioned throughout the space. The system employs sophisticated digital signal processing, which fine-tunes the audio output to achieve optimal acoustics tailored to the room’s characteristics.

An impressive characteristic of the YSP-3000 is the inclusion of 7-channel surround sound capabilities. This configuration ensures that users receive an immersive audio experience with clear dialogue and rich sound effects, ideal for movies, music, and gaming. The built-in subwoofer further enhances the low-end frequencies, providing deep bass that adds a layer of excitement to any audio playback.

The YSP-3000 also features Yamaha’s proprietary YSP sound field processing, which allows users to choose from multiple sound field modes to match their audio content. From gaming to music listening, users can select the option that best complements their experience. The system also supports various audio codecs including Dolby Digital and DTS, ensuring compatibility with a wide range of media formats.

Connectivity options are another strong point of the YSP-3000. It includes multiple HDMI inputs, enabling seamless integration with various devices such as Blu-ray players and gaming consoles. Additionally, it features optical and analog audio inputs, making it versatile enough for older audio devices. The included remote control offers intuitive navigation through settings and modes, making operation easy for users of all levels.

Overall, the Yamaha YSP-3000 stands out as a user-friendly and feature-rich solution for anyone looking to elevate their home theater audio experience without the hassle of multiple speakers and complex wiring. With innovation at its core, the YSP-3000 delivers a sound experience that is both convenient and captivating.