Pelco IV SE manual Zones

Page 62

ZONES

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

ZONES

ZONE NUMBER

* * * ZONE NOT DEFINED * * *

<EDIT ZONE LABEL>

<EDIT ZONE>

ZONE ENABLED ZONE BLANKING

<CLEAR ZONE>

BACK

EXIT

A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra 4 and Spectra IV SE dome systems are capable of eight zones, each with a 20-character label.

To program a zone:

1.Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open, and the cursor moves to the right.

2.Move the joystick up or down to view selections. Press Iris Open to enter selection.

3.Use the joystick to position the cursor beside EDIT ZONE.

4.Press Iris Open. The Zone programming window appears on the monitor.

5.Follow the directions displayed on the monitor. After the left and right limit stops are set, the Zones menu reappears with the ZONE ENABLED option set to YES.

To edit a zone label:

1. Use the joystick to position the cursor beside EDIT ZONE LABEL.

2. Press Iris Open. The following appears on the monitor:

LABEL FOR ZONE

ZONE NUMBER ------

1234567890OK

ABCDEFGHIJCANCEL KLMNOPQRST

UVWXYZ.,-/SPACE

abcdefghijBACKSPACE klmnopqrst

uvwxyz*;:

3.Use the joystick to position the cursor beside a character. Press Iris Open to enter selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris Open.

4.When the label is completed, move the cursor to OK. Press Iris Open to return to the Zones menu.

To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:

1.Move the cursor beside ZONE ENABLED or ZONE BLANKING.

2.Press Iris Open. The cursor moves to the right.

3.Move the joystick up or down to view selections. Press Iris Open to enter selection. To clear a zone:

1.Use the joystick to position the cursor beside CLEAR ZONE.

2.Press Iris Open. Follow the instructions on the screen.

*This setting applies only to Pressurized Spectra IV dome systems.

62

C3412M (9/06)

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Spectra IV Spectra IV SE Series Dome Drives Page Contents Blank All Above/Blank All Below Activate Aux Current Reading Reset Alert Welcome SW2 Switches 1-3 Special System Settings InstallationSwitch Settings SW1 Receiver AddressSW2 Switches 4-5 Serial Port Settings SW2 Switches 6-8 Baud SettingsDome Drive Installation Dome Drive InstallationTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control Spectra Switch Setting AddressTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Configure Done Getting StartedHow to Operate Your Dome System Accessing Main Menu Preset Quick Programming GuideCM9500 Press the Spot Monitor keyNET300/NET350/NET4001A 16X LowLight Color Menu Tree Dome Settings Camera 22X EXview LowLight Black-White Menu Tree Reference Information Azimuth Elevation Zoom 22X EXview LowLight Color Menu Tree Alarm Settings AUX Alarm Number AUX 1 Mode 23X LowLight Day/Night Menu Tree Line Sync Presets Edit Detection Areas Preset Number 35X LowLight Day/Night Menu Tree Uvwxy Date Format MM/DD/YYYY Edit Event Label Language System Information Exit AdditionalDisplay Setup Label Positions Type of Lighting Dome SettingsCamera Auto FocusZoom Limit 16X Models DD4TC16 and DD4TC16-XHigh Zoom SpeedLOW Light Limit LOWIR CUT Filter DarkAGC Limit Advanced Camera SettingsShutter Speed Numeric ValueAuto Iris Auto iris is disabled, and control is always manualDetermined by the auto iris level setting Auto White Balance Level. Sharpness level settings range fromAuto Sharpness GainBacklight Compensation BLC There are two backlight compensation settingsOFF default Set the video output to one of the following Video LevelWide Dynamic Range NormalElectronic Image Stabilization Applies only to 35X modelsAuto Flip Motion SettingsThere are two auto flip modes On default Proportional PANAuto Scan PresetPark Time Frame ScanScan Speed Preset Freeze FrameThere are three preset freeze frame settings Image is never frozenScan Limit StopsManual Stop is reachedAzimuth Zero None Power UPPower UP Action Dome synchronizes to the internal clock Settings range from 0-359 degreesLine Sync Spectra PresetsFollowing presets are predefined for specific functions Becomes C3412M 9/06 Enable Motion Detection Edit Detection AreasMotion Detection Areas AUX Time Activate AUX CommandTriggers a command to AUX Edit SchedulePatterns Zones Window Blanking To set a window blanking areaReverse Clear WindowBlank ALL ABOVE/BLANK ALL below Blanks everything below a user-defined tilt angleResume AlarmsReset Delay SequenceMEDIUM/LOW Normally open Momentary AUXLatching Title Text Edit Title TextAlert RepeatActivate AUX Reset AlertACK Action Current ReadingClear Password Fixed Date Power LineClock Repeat steps b-d for the ending date and time Follow the instructions in for Fixed DATE, adding Week Event Label EventEvent Type Edit Event Label Edit Event LabelHolidays have no effect on the event Edit EventDate is in the list of holidays Holiday Clear EventList Event April Edit HolidayHoliday occurs on the same date each year Clear Holiday List HolidaysScheduled Events Use this page to record scheduled eventsCycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Ntsc Specifications16X Models PALLux at 1/2 sec. shutter speed 22X Models Monochrome3.9/6.3 seconds Lux at 1/1.5 sec. shutter speed22X Models Color DD4C2223X Models Interlace Inch CCDLux at 1/1.5 sec. shutter speed B-W Zoom Speed 4.2/5.8 seconds Horizontal Angle of ViewLux at 1/50 sec. shutter speed B-W 35X Models DD4CBW35Lux at 1/3 sec. shutter speed color Zoom Speed 4.6/6.6 seconds Horizontal Angle of ViewLux at 1/50 sec. shutter speed color Product Warranty and Return Information ISO9001
Related manuals
Manual 80 pages 19.54 Kb

IV SE specifications

The Pelco IV SE is a leading-edge camera system designed specifically for surveillance applications that demand high-quality imaging, flexibility, and robustness. With its sleek design and advanced features, the Pelco IV SE is an essential tool for security professionals aiming to enhance situational awareness and improve monitoring capabilities.

One of the key features of the Pelco IV SE is its impressive image quality. The camera is equipped with advanced image sensors that provide high resolution and clarity, ensuring that critical details are captured even in challenging lighting conditions. Its enhanced low-light performance enables efficient operation in darkness, making it suitable for both day and night surveillance tasks.

In terms of technology, the Pelco IV SE incorporates advanced video compression algorithms, such as H.264 and H.265. These technologies allow for efficient bandwidth utilization while maintaining video quality, enabling long-term storage of data without sacrificing clarity. The camera also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single cable, reducing clutter and setup complexity.

Another standout characteristic is its flexibility. The Pelco IV SE is designed for various mounting options, including wall, ceiling, and pole mounts, making it adaptable for different environments and surveillance needs. The camera features a varifocal lens, allowing users to adjust the field of view to capture images from different distances, thus optimizing surveillance coverage.

Additionally, the Pelco IV SE integrates seamlessly with existing security systems, providing compatibility with various video management software platforms. This interoperability ensures that users can incorporate the camera into their broader security infrastructure without significant disruption.

The device also comes with intelligent video analytics capabilities, such as motion detection and facial recognition, enhancing its functionality. These features allow for proactive monitoring, where alerts can be set up for suspicious activities, ensuring timely responses to potential threats.

With its robust construction, the Pelco IV SE is built to withstand harsh environmental conditions. It adheres to specific IP ratings, indicating its resistance to dust and water, making it an ideal choice for both indoor and outdoor surveillance applications. In summary, the Pelco IV SE is a versatile, high-performance camera that combines advanced imaging capabilities, reliable technology, and extensive adaptability to meet the evolving demands of modern security surveillance.
Top Page Image Contents