Pelco IV SE manual Reverse, Clear Window

Page 64

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

WINDOW BLANKING

STYLE

BLANK ALL ABOVE

BLANK ALL BELOW

<SET WINDOWS>

BACK

EXIT

SET WINDOWS

WINDOW NUMBER

<EDIT WINDOW LOCATION> <EDIT WINDOW ZOOM> <EDIT SCHEDULE>

ENABLE WINDOW

REVERSE

CLEAR WINDOW

BACK

EXIT

6.The blanked area can be programmed to turn on or off at a specified zoom point. To set the zoom point:

a.Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open.

b.Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point.

NOTES:

•Since the area is already blanked out, it may be difficult to determine when you want window blanking to turn on. Reverse the window before setting the zoom point. When finished reverse the window again to blank out the area.

•Increase the size of the window if any part of the blanked area is revealed during pan, tilt, and zoom operations.

Window Blanking Disabled

Window Blanking Enabled

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu in the Event section with the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

For instructions on changing the features in the Edit Schedule menu, refer to the Edit Event menu in the Event section.

REVERSE

A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the blanking area remain visible. Reversing the window a second time will return it to its original condition.

CLEAR WINDOW

All areas that have been set for window blanking are cleared.

*This setting applies only to Pressurized Spectra IV dome systems.

64

C3412M (9/06)

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Spectra IV Spectra IV SE Series Dome Drives Page Contents Blank All Above/Blank All Below Activate Aux Current Reading Reset Alert Welcome Installation Switch SettingsSW2 Switches 1-3 Special System Settings SW1 Receiver AddressSW2 Switches 4-5 Serial Port Settings SW2 Switches 6-8 Baud SettingsDome Drive Installation Dome Drive InstallationTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control Spectra Switch Setting AddressTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Configure Done Getting StartedHow to Operate Your Dome System Accessing Main Menu Preset Quick Programming GuideCM9500 Press the Spot Monitor keyNET300/NET350/NET4001A 16X LowLight Color Menu Tree Dome Settings Camera 22X EXview LowLight Black-White Menu Tree Reference Information Azimuth Elevation Zoom 22X EXview LowLight Color Menu Tree Alarm Settings AUX Alarm Number AUX 1 Mode 23X LowLight Day/Night Menu Tree Line Sync Presets Edit Detection Areas Preset Number 35X LowLight Day/Night Menu Tree Uvwxy Date Format MM/DD/YYYY Edit Event Label Language System Information Exit AdditionalDisplay Setup Label Positions Dome Settings CameraType of Lighting Auto FocusZoom Limit 16X Models DD4TC16 and DD4TC16-XZoom Speed LOW Light LimitHigh LOWIR CUT Filter DarkAdvanced Camera Settings Shutter SpeedAGC Limit Numeric ValueDetermined by the auto iris level setting Auto iris is disabled, and control is always manualAuto Iris Level. Sharpness level settings range from Auto SharpnessAuto White Balance GainOFF default There are two backlight compensation settingsBacklight Compensation BLC Video Level Wide Dynamic RangeSet the video output to one of the following NormalElectronic Image Stabilization Applies only to 35X modelsMotion Settings There are two auto flip modes On defaultAuto Flip Proportional PANPreset Park TimeAuto Scan Frame ScanPreset Freeze Frame There are three preset freeze frame settingsScan Speed Image is never frozenLimit Stops ManualScan Stop is reachedAzimuth Zero Power UP Action Power UPNone Line Sync Settings range from 0-359 degreesDome synchronizes to the internal clock Following presets are predefined for specific functions PresetsSpectra Becomes C3412M 9/06 Enable Motion Detection Edit Detection AreasMotion Detection Areas Activate AUX Command Triggers a command to AUXAUX Time Edit SchedulePatterns Zones Window Blanking To set a window blanking areaReverse Clear WindowBlank ALL ABOVE/BLANK ALL below Blanks everything below a user-defined tilt angleAlarms Reset DelayResume SequenceMEDIUM/LOW Normally open Latching AUXMomentary Title Text Edit Title TextAlert RepeatReset Alert ACK ActionActivate AUX Current ReadingClear Password Clock Power LineFixed Date Repeat steps b-d for the ending date and time Follow the instructions in for Fixed DATE, adding Week Event Type EventEvent Label Edit Event Label Edit Event LabelDate is in the list of holidays Edit EventHolidays have no effect on the event List Event Clear EventHoliday Holiday occurs on the same date each year Edit HolidayApril Clear Holiday List HolidaysScheduled Events Use this page to record scheduled eventsReset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Specifications 16X ModelsNtsc PAL22X Models Monochrome 3.9/6.3 secondsLux at 1/2 sec. shutter speed Lux at 1/1.5 sec. shutter speed22X Models Color DD4C2223X Models Interlace Inch CCDLux at 1/50 sec. shutter speed B-W Zoom Speed 4.2/5.8 seconds Horizontal Angle of ViewLux at 1/1.5 sec. shutter speed B-W 35X Models DD4CBW35Lux at 1/50 sec. shutter speed color Zoom Speed 4.6/6.6 seconds Horizontal Angle of ViewLux at 1/3 sec. shutter speed color Product Warranty and Return Information ISO9001
Related manuals
Manual 80 pages 19.54 Kb

IV SE specifications

The Pelco IV SE is a leading-edge camera system designed specifically for surveillance applications that demand high-quality imaging, flexibility, and robustness. With its sleek design and advanced features, the Pelco IV SE is an essential tool for security professionals aiming to enhance situational awareness and improve monitoring capabilities.

One of the key features of the Pelco IV SE is its impressive image quality. The camera is equipped with advanced image sensors that provide high resolution and clarity, ensuring that critical details are captured even in challenging lighting conditions. Its enhanced low-light performance enables efficient operation in darkness, making it suitable for both day and night surveillance tasks.

In terms of technology, the Pelco IV SE incorporates advanced video compression algorithms, such as H.264 and H.265. These technologies allow for efficient bandwidth utilization while maintaining video quality, enabling long-term storage of data without sacrificing clarity. The camera also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single cable, reducing clutter and setup complexity.

Another standout characteristic is its flexibility. The Pelco IV SE is designed for various mounting options, including wall, ceiling, and pole mounts, making it adaptable for different environments and surveillance needs. The camera features a varifocal lens, allowing users to adjust the field of view to capture images from different distances, thus optimizing surveillance coverage.

Additionally, the Pelco IV SE integrates seamlessly with existing security systems, providing compatibility with various video management software platforms. This interoperability ensures that users can incorporate the camera into their broader security infrastructure without significant disruption.

The device also comes with intelligent video analytics capabilities, such as motion detection and facial recognition, enhancing its functionality. These features allow for proactive monitoring, where alerts can be set up for suspicious activities, ensuring timely responses to potential threats.

With its robust construction, the Pelco IV SE is built to withstand harsh environmental conditions. It adheres to specific IP ratings, indicating its resistance to dust and water, making it an ideal choice for both indoor and outdoor surveillance applications. In summary, the Pelco IV SE is a versatile, high-performance camera that combines advanced imaging capabilities, reliable technology, and extensive adaptability to meet the evolving demands of modern security surveillance.
Top Page Image Contents