Yamaha RX-V730 owner manual Poor bass reproduction, Problem, Remedy Refer

Page 65

Problem

The sound suddenly goes off.

Only the speaker on one side can be heard.

No sound from the effect speakers.

No sound from the center speaker.

No sound from the rear speakers.

No sound from the subwoofer.

Poor bass reproduction.

Cause

The protection circuit has been activated because of a short circuit, etc.

The sleep timer has functioned.

The sound is muted.

Incorrect cable connections.

Incorrect setting of "5 L/R BALANCE" on the SET MENU.

The sound effect is off.

A Dolby Surround, Dolby Digital or DTS decoding DSP program is being used with material not encoded with Dolby Surround, Dolby Digital or DTS.

A 96-kHz sampling digital signal is being input to this unit.

The output level of the center speaker is set to minimum.

"IA CENTER" on the SET MENU is set to NON.

One of the Hi-Fi DSP programs (l to 4) has been selected (except for 6ch Stereo).

The source encoded with a Dolby Digital or DTS signal does not have a center channel signal.

The output level of the rear speakers is set to minimum.

A monaural source is being played with program 9.

"IE BASS" on the SET MENU is set to MAIN when a Dolby Digital or DTS signal is being played.

"IE BASS" on the SET MENU is set to SWFR or MAIN when a 2-channel source is being played.

The source does not contain low bass signals (90 Hz and below).

"IE BASS" on the SET MENU is set to

SWFR or BOTH and your system does not include a subwoofer.

The speaker mode settings (main, center, rear, or rear center) on the SET MENU does not match your speaker configuration.

iiPlq:l_-Wlqqili'l _

 

 

 

 

Remedy

Refer

 

 

 

 

 

 

 

 

to page

Check

the IMPEDANCE

SELECTOR switch is set

12

to the appropriate position and then turn this unit

 

 

back

on.

 

 

 

 

 

 

 

Check the speaker wires are not touching each other

 

 

and then turn this unit back on.

 

 

Turn on the power, and play the source again.

 

 

Press MUTE or any operation buttons of this unit to

 

 

cancel a mute and adjust the volume.

 

 

Connect

the cables

properly.

If the problem persists,

10,

11

the cables

may

be

defective.

 

 

 

Adjust

it

to the

appropriate

 

position.

45

 

Press

STEREO/EFFECT

to

turn it on.

29

 

Select

another

DSP program.

 

27 -

34

Raise

the

level

of the center

speaker.

52

Select

the

appropriate

mode

for your center speaker.

42

Select

another

DSP

program.

 

27 - 34

Raise

the output level of the rear speakers.

52

Select

another

DSP program.

27 - 34

Select

SWFR

or BOTH.

43

Select

BOTH.

 

43

Select

MAIN.

43

Select

the appropriate position for each speaker

42 - 44

based on the size of the speakers in your

 

configuration.

 

61

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Page Riskof Electricshock Donotopen Ansi FOG Information for US customers onlyNfpa FCCYamaha We Want You Listening For a LifetimeFor Canadian Customers Contents Features Getting Started DIGITAL. EX ProcessingAbout this manual Korea and General models A., Canada, China75-ohm/300-ohm antenna Europe, U.K., Australia Adapter U.K. model Singapore modelsInput Mode Remote control sensorFront panel display STANDBY/ONMemory MANL/AUTO FM PRESET/TUNING EditTuning Mode AUTO/MANL Mono Level Standby@ Test RE-NAMESelect A/V Handling the remote controlSET Menu I1 on ScreenTuned indicator Volume level indicatorMemory indicator Auto indicatorMain speakers Use of a subwoofer expands your sound fieldCenter speaker Rear speakersSpeaker cables Connecting to the SpeakersTerminals Main Speakers terminalsMain Speaker Right Left Center Subwoofer Rear center System Subwoofer jackImpedance Selector Impedance Selector switchSwitch Connecting to digital jacks Connecting a DVD player/digital TV/cable TV Connecting a video monitorConnecting a game console or Camcorder Connecting a VCR or DVR digital Video recorderVideo monitor Indicates Signal Direction Left analog Cables Right AnalogConnecting a CD recorder or MD Connecting a CD playerConnecting a turntable RecorderFrequency Step switch China and General Models Connecting the AM loop antenna75-ohm/300-ohm antenna adapter U.K. model Included Indoor FM Antenna AM loop antennaMain jacks Subwoofer jackRear Center jack Center jackAC Outlets Switched Connecting the AC power cordSTANDBY/ON System Power China and General modelsShort display Full displayDisplay off Full display Short DisplayNrm Normal/-10 dB CenterAMP Press AMP to selectTo output TestEffect speakers using Adjust the levelSo that it matches Level of the mainTo select Main SpeakersTo be used =ii=To mute the sound When you have finished using This unitBGV background video function II E Input modeSub-program name Program 1 Program nameOwH Program Selecting PRO LogicPlaying Dolby Digital Surround EX or DTS ES software Matrix indicator lights upVirtual Cinema DSP Silent Cinema DSPDisco Program FeaturesRecreating a sound field Page Dolby Digital EX/DTS-ES compatible + DSP sound field effect Dolby Digital/DTS + DSP sound field effectDolby Pro Logic + DSP sound field effect Dolby Pro Logic ITTable of Program Names for Each Input Format For movie programs No toChannel Channel StereoTheater For audio-video sources No toManual tuning Automatic tuningPress PRESET/TUNING / once to begin automatic tuning Goesoff231 Automatic preset tuning optionsFor FM stations Memory back-up2,5 Manually presetting stationsTune in to a station Press Memory MANL/AUTO FMPress PRESET/TUNING Edit again Press and hold PRESET/TUNING Edit for more than 3 seconds31,3 2,4 Tt c.,, .=M ¢ h1LJTo set Amount of time P P I 7Fir,iFMemory back-up Special considerations when Recording DTS softwareTimer playback/recording Speaker SET Center Input ModeMain Rear LRLRG 1A Center center speaker ModeSML NON1C Rear LR rear speaker mode 1B Main main speaker mode1D Rear CT rear center speaker mode 1E Bass LFE/bass out modePress to adjust the LFE level 1F Main Lv main level modeSTD MAXPress repeatedly to exit from Input RenameDimmer Blue BackPage Component control area Controlling this unitControlling other component Press Code SET again to exit from the setup Mode Press Code SET using a ballpoint pen or similar objectIi i!!!i liiI Ii iPress / to move the cursor to the next Position Press RE-NAME again to exit from Renaming modeJiiiiiiJi I il ill setup manufacturer code for Component control Press a / v to select the clear modePress and hold Clear again for about 3 seconds Ii ii hiClearsall renamedsourcenamesDVD player AMP ? £ i ir,?Reverberations Elements of a sound fieldEarly reflections Press To change Example of the parameter setting displayValue Program No. Program name CursorRoom Size for the presence sound field Room SizeLiveness INIT. DLY Surround initial delayLiveness Surround liveness REV.TIME REV. Delay Reverberation delayReverberation Time REV. Level Reverberation levelFor 6ch Stereo DimensionPanorama CtwidthGeneral Remedy Refer ProblemPoor bass reproduction Cause ProblemRemedy Refer This unit does not operate properlyProblemCause Remote controlPreviously preset stations can no longer be tuned TunerSilent Cinema DTS Digital Theater SystemsCinema DSP PCM Sampling Frequency and numberVideo Section Audio SectionFM Section AM SectionOyamaha

RX-V730 specifications

The Yamaha RX-V730 is a noteworthy home theater receiver, particularly well-regarded for its blend of performance, features, and versatility. Introduced in the early 2000s, this model serves as a testament to Yamaha’s commitment to crafting high-quality audio components that cater to both casual listeners and audiophiles alike.

At its core, the RX-V730 supports a robust surround sound experience with its 6.1 channel output, allowing users to immerse themselves in multi-dimensional audio. It boasts an impressive power output of up to 100 watts per channel, producing clear and dynamic sound that enriches movies, music, and games. The hallmark of the RX-V730 is its compatibility with various surround sound formats, including Dolby Digital EX and DTS-ES, enabling it to create a captivating acoustic environment that faithfully reproduces the sounds from modern film soundtracks.

One of the RX-V730's significant features is its Digital Signal Processing (DSP) technology. With multiple DSP modes at users' disposal, such as concert hall and jazz club, the receiver enhances audio playback to replicate the acoustics of different environments, creating a customizable listening experience tailored to individual preferences. This technology ensures that soundtracks and audio tracks maintain clarity and power, regardless of the source material.

Connectivity is also a strong suit of the RX-V730. It includes a variety of inputs, such as multiple digital inputs (both optical and coaxial) for connecting to CD players, DVD players, and gaming consoles. It also features an array of analog inputs and outputs, along with a dedicated subwoofer output, providing flexibility for system configuration. Furthermore, the receiver supports video switching capabilities for composite and S-Video inputs, making it a versatile hub for home entertainment systems.

In terms of user interface, the RX-V730 is designed with intuitive on-screen menus, making setup and operation user-friendly. The remote control offers convenient access to various functions, ensuring that users can manage their audio and video setup with ease. The learning function of the remote allows it to control other devices, making it a comprehensive tool for managing an entire home theater system.

The Yamaha RX-V730, with its blend of innovative technologies, high-quality sound reproduction, and user-friendly features, provides an excellent option for those looking to enhance their home audio experience. Whether it’s a movie night, a family gathering, or an immersive gaming session, this receiver delivers the audio performance needed to make any experience memorable.
Top Page Image Contents