JAI TMC-4200GE Video Depth, Click on the option button to set the preferred option

Page 52

Page 40

Dual-Tap TM-4200GE AccuPiXEL Series Camera-Control Software

FIGURE 39. The R Auto Offset box is checked only while the command is being set by the camera.

Tap Selection:

The TM-4200GE is capable of Dual-Tap or Single-Tap operation. Click the option button for the operation you prefer. Single-Tap operation does not allow the higher data rate permitted by the Dual- Tap output.

FIGURE 40. Click on the option button to set the preferred option.

6.5.4Video Depth

FIGURE 41. Use the option buttons to select 8-bit, 10-bit, or 12-bit output.

FIGURE 42. Image Pre-processing

Cover the lens with the lens cap before enabling the blemish calibration. Activate this control by clicking the Blemish Calibration button and then check the “Enable Blemish Compensation” check box. The blemish compensation activates.

Note: Blemish Calibration is necessary only after a camera has been powered off and restarted. Once enabled, blemish compensation remains active unless the user unchecks the “Enable Blemish Compensation” check box.

Introduction

Image 52

Contents TM/TMC-4200GE Progressive Scan Cameras Page CE Compliance JAI IncPage Table of Contents Table of Contents IntroductionTroubleshooting Table of Contents List of Figures List of FiguresList of Figures List of Tables List of Tables Software Introduction Scope of the DocumentRelated Documents Gigabit Ethernet Camera InterfaceBefore Installing the GigE Series Camera-SDK Software Software InstallationInstalling the Software Uninstalling the Software Scanning for DriversQuick-Start Change and Remove ButtonsSelect Camera Window Connectors Power and Signals ConnectorHirose Connector, Pin Assignment ConnectorsGigE EthernetSetup Configuring the TM-4200GE CameraConfiguring the TM-4200GE Camera Advanced Configuration Window Configuring the Imager Integrated GigE Camera SoftwareConfiguring the Internal Frame Grabber TM-4200GE Software GUI FeaturesCheck the Current Camera Setting ModesAdvanced Configuration Port Communication Exposure ControlShutter Mode Shutter SpeedProgrammable Scan TM-4200GE Software Scan ModeUser Programmable Variable Partial Scan Programmable Scan Set Dialog Box TM-4200GE Software Gain Settings GainGain R Auto Gain ControlLook-Up Table Memory PagesExternally Triggered Free-Running ModeInternally Triggered TM-4200GE Software Save/Restore Settings to Your Hard Disk White Balance Control Color Versions OnlyTM-4200GE Software Main Menu Option VersionExit Test PatternSignal Handling Signal HandlingCamera Inputs Camera OutputsGE Camera Gpio Control Block Gpio Look-Up Table Gpio Label Table Input Signal Description LabelGpio Look-Up Table Input Labels Pulse Generators Output label Signal DescriptionGpio Look-Up Table Output Labels Pulse Generator GigE Series Camera Serial Commands TM/TMC-4200 Command ListScan Mode GigE Series Camera Serial CommandsChannel Balance VsubDual Tap Digital Video Output Order Image Pre-processingCommand Responses Parameter End of Cmd Description Command Parameter End of Cmd Description0000=Async no shutter 0001 1000=Async Introduction Dual-Tap TM-4200GE AccuPiXEL Series Camera-Control SoftwareDual-Tap TM-4200GE AccuPiXEL Series Camera-Control Software IntroductionAccuPIXel Setup screen Using the GigE mode TM/TMC-4200GE CameraGUI Features Main DualTap AccuPiXEL WindowOperating The Control Software Introduction Scan Area Scan Area drop down boxGain Control Offset VoltageVideo Depth Click on the option button to set the preferred optionLUT Look-Up Table Positive or Negative LUT SelectionDual-Tap TM-4200GE AccuPiXEL Series Camera-Control Software Password EepromLoad SaveDual-Tap TM-4200GE AccuPiXEL Series Camera-Control Software Hardware Introduction Product DescriptionTM-4200GE Hardware Hardware IntroductionFeatures Installation Accessories and OptionsGetting Started Unpacking InstructionsCamera Setup Connector Pin Configurations2 a 12-Pin Connector Pin ConnectorEthernet Connector Power Supplies and Power Cable SetupPower Supplies JAI Inc. Power Cables Building Your Own Power CableAttaching the Power Cable to the Connector 12P-02S Interface Cable Pin# Lead Color FunctionAdjustable Back-Focus TM-4200GE Hardware Attaching the Camera LensPreset Scan Area OperationProgressive Scanning OperationTM-4200GE Hardware Programmable Scan Area Full Scan Area 2x2 Binning BayerSub-sampling Digital Zoom X2 BinningSub-sampling Digital Zoom TM-4200GE Hardware Bayer Color Filter Color Versions Sub-sampling Digital Zoom Scan Area Start PointsTM-4200GE Hardware Color Filter Array Bayer Color Filter Array CFATM-4200GE Hardware Starting Pixel Configuration Sync and DataCamera Functions Example of TMC-4200GE Same as TM-4200GETM-4200GE Hardware Timing Chart Scan ModeInterpolation Software Electronic ShutterColor Interpolation TM-4200GE Hardware Preset Shutter Programmable Exposure-Continuous ModeAsynchronous No Shutter Mode Electronic Preset ShutterAsynchronous Programmable Exposure Mode External Trigger TimingPulse Width Control Mode Asynchronous Programmable External TriggerParticle Imaging Velocimetry Fixed Exposure Mode Pulse Width Control TriggerTM-4200GE Hardware PWC PIV Mode PWC PIV Timing Table Asynchronous Mode ChartDynamic Range Control Programmable Look-Up Table LUT and Knee ControlCamera Timing Charts External Sync and Pixel LockingScan Data Horizontal pixels Area ClockExternal HD Locking and External VD Reset Async ResetAsync Reset Timing Scan AH lines Area AI lines Lines Μsec Sec LinesTroubleshooting Problems and SolutionsSymptom No Video Symptom Dark VideoSymptom Notebook Computer Driver Installation Problems TM-4200GE Hardware Symptom Video does not Display ProperlyInformation and Support Resources Specifications TM-4200GE Camera Specifications TableAppendix AppendixTM-4200GE Hardware 11.1.1 TM-4200GE Physical Dimensions Physical DimensionsTM-4200GE Hardware Spectral Response Spectral ResponseAppendix Page W . j a i . c o m