JAI CV-M40 operation manual Pulse width control mode, Frame-delay readout mode

Page 9

CV-M40

a)Set SW1-5 at ON, and SW1-6 at OFF to select the Edge pre-select mode.

b)Set SW1-1 to SW1-3 to select the appropriate shutter speed. For controlling the shutter speed by the RS 232C serial interface, set SW1-8 at ON.

c)Set the SW1-4 switch to ON to select the Binning mode and set the switch SW1-7 to OFF to select the Partial scan mode.

CAUTION

The pulse width of the external trigger pulse must be 2H to 1300H.

6-2-2. Pulse width control mode

In this mode, the exposure time is controlled by the pulse width of external trigger pulse. The exposure starts at the falling edge of the external trigger pulse and ends at the rising edge of the external trigger pulse. The WEN pulse is generated and output from the camera.

For details, refer to the timing charts section of this manual.

To use this mode, set up the camera as follows ;

a)Set SW1-5 at OFF, and SW1-6 at ON to select the Pulse width control mode.

b)Set the SW1-4 switch to ON to select the Binning mode and set the switch SW1-7 to OFF to select the Partial scan mode.

CAUTION

The pulse width of the external trigger pulse must be 2H to 525H.

6-2-3. Frame-delay readout mode

In this mode, the timing of the video output is controlled by the width of the external trigger pulse. The exposure starts at the falling edge of the external trigger pulse and ends according to the shutter setting. The video signal is output at the rising edge of the external trigger signal. The WEN pulse is generated and output from the camera.

For details, refer to the timing charts section of this manual.

To use this mode, set up the camera as follows ;

a)Set SW1-5 at ON, and SW1-6 at ON to select the Frame-delay readout mode.

b)Set SW1-1 to SW1-3 to select the shutter speed.

c)Set the SW1-4 switch to ON to select the Binning mode and set the switch SW1-7 to OFF to select the Partial scan mode.

CAUTION

The minimum value of pulse width for the external trigger pulse depends on the exposure time, as follow. Minimum : pulse width (more than 3H) > exposure time

9

Image 9
Contents CV-M40 EN-50081-1 EN-50082-1 89/336/EECTable of Contents Pin connector HR10A-10P-12S-01 Pin connector HR10A-7P-6S Main FeaturesGeneral Standard compositionCCD sensor Lens mount IT CCD sensor Mount type Locations and functionsPin connector DC IN/SYNC connector Pin assignmentIntSyncMode Output Pin connector Trigger connectorMale RXDinputExt. trigger/readout mode Input/output of HD/VD signalEdge pre-select mode Functions and operationsFrame-delay readout mode Pulse width control modeVideo out H Timing chartsPositive Negative494H Validperiod WENNegative 87HWaitingforExt.Trigger Notre-setatHDsync21H=3or1.777HDisSnotmentined 660Ext.Trig Frame-delay readout modeSW1 switch on the rear panel Mode settingShutter speed SW1-1, SW1-2, SW1-3 ShutterBinning mode SW1-4 Partial scan SW1-7RS 232C interface SW1-7 Jumpers on PK8202 board Jumpers on boardRestTrigger6P12P12P TothefollowingtriggersEdgePr-selectModeExt.SyncTrigger12P Jumpers PK8273 board JumpB3Jump Ing output, it becomes High level JP22 WEN Polarity ReversingUnit mm inch External appearanceSpecification Ensitivitysizeratio horizontalverticalMonochorme1/2ITCCDsensorprogressivescan Appendix User’s Record 2700-11114 E C1